ASUS WL-500W Oleg Custom Firmware 1.9.2.7-9 Download

Posted at November 21, 2024 by PCI-DB Team

ASUS WL-500W Oleg Custom Firmware 1.9.2.7-9 Description

Changes: 

 - Added RTC support for the WL-HDD/WL-700g boards
- Fixed a bug causing lockups during reboot
- SNMP: uptime values no longer depends on the system time
- UPnP: it's now possible to select interface for which interface address reported back to clients (IP Config - Misc), port-forwards are working just like other virtual servers
- UPnP: additionally protected by built-in firewall in case when multicast forwards enabled
- IPTV: added udpxy (check IP Config - Miscellaneous: IPTV UDP Multicast to HTTP Proxy Port) to enable-disable it
- Added Get IP automatically option to the WAN & LAN page
- DHCP: added support for some broken DHCP servers (e.g. Golden Telecom)
- Manual DNS server entries are no longer added to routing table
- Fixed Redirects in the web-iface (it should no longer redirect to internal address);
- Enabled Idle Disconnect functionality for PPPoE/PPTP. It's recomended to turn this feature off by typing zero in this field.
- L2TP speed increase (up to 2.5 times compared to previous versions) and correct tunnel termination
- PPTP sync option is now correctly handled and enabled by default, improved overall stability, cleared up logs;
- Updated QuickSetup to recent PPPoE, PPTP and L2TP changes
- Added fine grained WPA control on the Wireless page: added separate WPA Enterprise, WPA2 Enterprise, WPA Personal, WPA2 Personal and WPA-Auto-Personal (which is wpa-psk + wpa2-psk for TKIP+AES, wpa-psk for TKIP and wpa2-psk for AES).
- Added Regulatory Mode field (802.11d/802.11h/off) to the Wireless - Advanced page. This should fix some problems with Intel WiFi cards (select 802.11d mode).
- Virtual Servers has now separate default action in the WAN to LAN firewall.
- Added Host Name field to the Manual DHCP MAC list.
- Added Comment field to Wireless - Access list.
- FTP: switched to vsftpd, reworked web-iface.
- Samba: extended web-iface, new share modes - all partitions, manual share list.
- Samba: Windows Vista support, W2K3SP1 compatibility
- Added utf8 as default encoding of the hard/flash drive (enabled by default).
- NFS: fixed some /etc/exports problems
- Kernel modules are now stored in single directory
- Added ftdi_sio usb to serial converter module
- Some other modules are now available as separate download (modules-1.9.2.7-9.tgz), includes HID, input, Bluetooth. Unpack them to /opt
- Added modprobe, which is looking for /opt/lib/modules/... by default.
- USB updates
- VLAN support fixes, updated robocfg
- dropbear 0.50 (credits to lly), enabled inetd support
- busybox_httpd fixes: new cgi environment vars (HTTP_HOST, CGI_*)
- Changed a way how automount works: everything is mounted to /tmp/mnt now, while /tmp/harddisk is just a symbolic link to first partition
- Samba/FTP/NFS relative paths are against /tmp/harddisk
- Added /usr/local/sbin/pre-mount to be called before automount (suitable to manual mounts, disk checks, etc).
- Added Enable USB Storage selection to the System Setup - Services page to enable usb storage modules to load automatically
- Added filesystem type autodetection to automount partition

Important changes:

To reset username/password you've to reset to defaults using a RESET/RESTORE button!
- Port numbers used for RAW printing are changed: use 9100 for USB and 9101 for LPT
- Root fs is now ext3
- All scripts should now have
#!/bin/sh
line, otherwise they will not work
- post & pre scripts are now stored in the /usr/local/sbin directory; there is no /usr/local/init anymore
- post-firewall script should be adjusted, be careful when adding rules with -A - this will no longer work correctly, due to unconditional rule. Check the iptables -L -v output
- Client mode is not supported by the WL-500bv2 units

WARNING:

DON'T TRY CUSTOM FIRMWARES UNLESS YOU KNOW WHAT YOU ARE DOING, YOU COULD DESTROY YOUR UNIT BY DOING THIS! I'M NOT RESPONSIBLE TO ANY DAMAGE CAUSED TO YOUR UNIT BY USING IT! USE ON YOUR OWN RISK!

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Oleg Drivers