1. Driver
  2. Firmware
  3. D-Link DES-3028P Fast Ethernet L2+ Switch Firmware 2.00B27

D-Link DES-3028P Fast Ethernet L2+ Switch Firmware 2.00B27 Download

Posted at December 4, 2023 by PCI-DB Team

Install Driver Automatically
Device NameD-Link DES-3028P Fast Ethernet L2+ Switch Firmware 2.00B27
File Size2.1 MB
Supported OSWindows All

D-Link DES-3028P Fast Ethernet L2+ Switch Firmware 2.00B27 Description

- Support new model DES-3028G
- 802.1D 2004 edition
- Root Restriction (defined in 802.1Q-2005)
- MLD Snooping v1 and v2 awareness
- DoS attack Prevention
- Asymmetric VLAN
- IP-MAC-Port Binding v3.3
- IMPB auto recovery
- IGMP authentication
- VLAN trunking
- Loopback detection v2.0
- Support Port-based QinQ (TPID of outer tag cannot be configured to 0x8100)
- Cable Diagnostics
- Gratuitous ARP
- Password encryption
- Extend trusted host number to 10 entries and add mask function on trusted host
- Support data driven multicast learned automatically
- Support limited IP multicast address ranges
- Product serial number can be displayed on GUI, CLI and be queried via SNMP. (From new shipment and burn-in serial number in H/W)
- Password Recovery v1.1
- Support VLAN batch configuration
- Be able to force the 802.1X client to go offline
- Support 802.1X session timeout attribute
- Can assign ingress/egress bandwidth control and 802.1p priority to the port according to the attributes dispatched from Radius Server
- Support “show tech support” command for troubleshooting
- Support configurable MDI/MDIX, it can be manual configure as Auto, Normal and Cross mode
- Remark DSCP to 802.1p priority tag
- Extend dynamic VLAN groups to 255
- Support three MAC address format: 11-22-33-44-55-66, 11:22:33:44:55:66 or 112233445566
- Add auto complete commands with extra parameter “force_agree”. Instead of popping up (Y/N) message while enter reset and reboot, it will be executed automatically
- Remove all ACL entries by one command in CLI, Web and SNMP
- Remove all trust host entries by one command in CLI, Web and SNMP
- Display remaining ACL rules on Web/CLI
- Add a SNMP MIB to support VLAN advertisement enable/disable function
- Add show memory usage/percentage SNMP MIB
- Add an OID to show port utilization
- Add an OID to clear FDB and ARP table
- Add ping command to user privilege
- Stop contacting to TACAS+ server periodically before logging-in
- Add “show VLAN” command by VLAN ID
- Add "show FDB VLAN" command by VLAN ID
- Support tagged ports column while show VLAN
- Support forbidden router port
- Add the ability to forward the unregistered multicast traffic to router port even when the ‘filter unregistered groups’ option is enabled
- Add RFC2869 RADIUS extension standard to get 64 bits counters from two attribute "Acct-Input-Gigawords & Acct-Output-Gigawords"
- Support to get NAS-ID from switch "system name" and can be configure NAS-ID
- Support DHCP relay option 82 remote ID
- Support DHCP local relay to insert option 82 information on DHCP broadcast packets in client’s VLAN
- Block broadcast packet in DHCP relay
- Ability to set the row number of terminal line
- Add ARP-FDB table for easy set static entry to IP_MAC_Port binding tables
- Extend ACL access id number from 256 to 65535
- Remove the display of MAC address from telnet log
- Support broadcast storm control port shutdown log
- Support port information on STP log event while STP topology changes
- DLF rename to Unicast in storm control feature
- Redirect embedded URL of D-Link logo to local OBU web site
- Remove Web-UI welcome page
- If SIM commander switch connects to member switch via tag ports, it is unable to upload/download member’s configuration
- If STP is enabled on ports, ‘show ports’ command will cause screen to freeze
- If STP is disabled, show ports and then reset, it will cause high CPU utilization
- Show port list from left to right via SNMP
- Config ports command lacks learning enable/disable parameter
- While config multicast filter, unregistered groups on all ports cannot be learned as multicast router port
- X authentication process with PEAP protocol takes a long time to complete
- Incorrect display format while execute show current config
- MAC address search issue on FDB monitor function
- System interface cannot change to other VLAN while the switch is set as DHCP client
- CPU high utilization while STP and LBD are enabled at the same time
- Multicast client is unable to send leave packet if new VLAN is created on the switch
- Filter unregistered groups on the port will block multicast control packets
- IF customer uses SNMP module command and then powers off/on, switch will enter exception mode and reboot cyclically
- SIM feature only works on default VLAN
- While enable LACP connection, system interface cannot be accessed
- Different ACL rules sequence will make ACL entries configure fail
- SSH fatal error while running perl script from client
- Dynamic VLAN assignment does not work if the RADIUS server is Juniper Funk Steel
- While enable bandwidth control on port 25 and send packets over the rate limit from port 25 to 26, packet loss will occur from port 26 to 25

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related D-Link Drivers

D-Link DWA-645 Driver 1.02

Device Type: Network Card File Size: 7.4 MB Windows 9X ,Windows ME ,Windows NT ,Windows 2K ,Windows XP ,Windows 2003 ,Windows Vista ,Windows XP 64 bit ,Windows 2008 ,Windows Vista 64 bit ,Window

Install Driver

Find Missing Drivers

© 2023 PCI-DB.com - PCI Database Replacement. All rights reserved. Sites we love: Intec Expo, Solved Directory