Posted at December 23, 2024 by PCI-DB Team
Install Driver AutomaticallyDevice Name | Sony Alpha DSLR-A700K Camera Firmware 1.10 |
---|---|
Category | Scanner Digital Camera Webcam |
Manufacturer | Sony |
File Size | 4.6 MB |
Supported OS | Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows 8.1 ,Windows 8.1 64 bit ,Windows 10 ,Windows 10 64 bit |
- Adds a "2 steps/3 shots" option to the "Bracket: Single" and "Bracket: Cont." Drive mode settings for auto exposure bracketing.
- Adds an "Off" option to the "High ISO NR" (Noise Reduction) setting.
- Provides improvements in picture quality when using a high ISO setting; color noise is minimized in images captured using an ISO setting of 1600 or higher.
- Provides improvements to the Auto White Balance (WB), especially when taking pictures using the flash.
- Improves performance of the D-range Optimizer (DRO). The ability to discriminate between scenes has been improved, and the scope to which the advanced DRO effect can be applied has been broadened.
- Improves the ability to make a successful connection with the VG-C70AM vertical grip.
- Resolves an issue where the Access Lamp remains lit and the camera stops responding when several pictures are taken in rapid succession.
- Resolves an issue where powering the camera off while in "MR" mode may cause some registered settings to carry over to other shooting modes.
- Sharper images for pictures taken under low contrast conditions
- Reduced noise for pictures taken at ISO 3200
- Improved flash control for objects closer than 1 meter with non ADI controlled lenses
WARNING!!: When performing the firmware update, use a fully charged rechargeable battery pack NP-FM500H or the AC adapter AC-VQ900AM AC adapter/charger (sold separately). Do not remove the battery or AC adapter during the firmware updating, otherwise the camera may be permanently damaged.
- Slide the POWER switch to the ON position and set the "Memory card" to the type you are using for the update (Memory Stick Duo / CF card / Microdrive) in Setup Menu 2 , then slide the POWER switch to the OFF position.
- If it is not already there, insert the formatted recording media (Memory Stick Duo / CF card / Microdrive) into the camera
- Press and hold the MENU button. While holding the MENU button, slide the POWER switch to the ON position. Continue to press the MENU button until the confirmation window appears.
- The confirmation window appears.
- Use the Multi-selector to highlight "OK", then press the Center button of the Multi-selector. The Updating procedure will start.
- When the "Update is completed" message appears, the updating procedure is complete.
Note: The camera automatically restarts after about 5 seconds.
- Power off the camera, then remove the recording media.
Updating to a newer firmware version than the one already installed on your camera can improve the device’s overall performance and stability, resolve various issues, and add support for newly developed features or enhance existing ones.
On the other hand, downgrading the camera’s firmware can recover its functionality in the unlikely event the currently installed version is faulty or the device’s performance dropped after an upgrade. However, bear in mind that applying an earlier build might not always be possible.
It is recommended that changing the camera’s firmware be performed when the new release resolves an issue that your device has been encountering, or adds a new feature (or enhances an existing one) that could prove useful for you.
This process isn’t intended to be destructive, but still, it’s best to save all your personal data and configurations before applying a different firmware. Moreover, make sure that the battery is fully charged and don’t use the camera’s buttons while the installation is in progress.
When it comes to the update method, usually, you must copy the firmware file onto a compatible memory card, insert it into the camera, and browse from the menu to the device’s update section.
However, each device has various ways to enter the update mode and particular steps that should be taken for a successful upgrade, therefore make sure you read the product’s installation guide.
That being said, if you consider that this firmware improves your device in any way, then hit the download button and get the desired version; if not, check with our website as often as possible so that you don’t miss the update that will boost your camera’s performance.
It is highly recommended to always use the most recent driver version available.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.
Device Type: Tv Hdtv Projectors File Size: 1.5 GB OS Independent
Install DriverDevice Type: Tv Hdtv Projectors File Size: 1.5 GB OS Independent
Install DriverDevice Type: Firmware File Size: 1.2 MB Windows 9X ,Windows ME ,Windows NT ,Windows 2K ,Windows XP ,Windows 2003 ,Windows Vista ,Windows XP 64 bit ,Windows 2008 ,Windows Vista 64 bit ,Window
Install DriverDevice Type: Scanner Digital Camera Webcam File Size: 64.4 MB OS Independent
Install DriverDevice Type: Tv Hdtv Projectors File Size: 1.5 GB OS Independent
Install DriverDevice Type: Scanner Digital Camera Webcam File Size: 64.4 MB OS Independent
Install DriverDevice Type: Tv Hdtv Projectors File Size: 1.5 GB OS Independent
Install DriverDevice Type: Mobiles File Size: 43.6 MB Windows 2K
Install DriverDevice Type: Tv Hdtv Projectors File Size: 1.5 GB OS Independent
Install DriverDevice Type: Tv Hdtv Projectors File Size: 1.5 GB OS Independent
Install DriverFind Missing Drivers
Recent Devices
Recent Drivers
© 2024 PCI-DB.com - PCI Database Replacement. All rights reserved.