MikroTik RouterOS PPC Firmware 6.36 RC 11 Download

Posted at December 21, 2024 by PCI-DB Team

MikroTik RouterOS PPC Firmware 6.36 RC 11 Description

What's new in 6.36rc11:

- bonding - fixed crash on RoMON traffic transmit;
- bonding - implemented l2mtu value == smallest slave interfaces l2mtu;
- ipsec - added dead ph2 reply detection;
- ipsec - fixed AH with SHA2;
- firewall - added raw table to be able to disable connection tracking on selected packets or drop packets before connection tracking and packet defragmentation (CLI only);
- firewall - fixed policy routing configurations (introduced in 6.35rc38);
- queue - fixed interface queue type for ovpn tunnels;
- arm - added Dude server support;
- arm - fixed kernel failure on low memory;
- discovery - fixed identity discovery (introduced in 6.36rc5 and 6.35.1);
- firewall - added "/interface list" menu which allows to create list of interfaces which can be used as in/out-zone matcher in firewall (CLI only);
- log - fixed time zone adjustment (introduced in 6.36rc5 and 6.35.1);
- lte - added cinterion pls8 support;
- snmp - fixed snmp timeout (introduced in 6.36rc5 and 6.35.1);
- ssl - fixed memory leak on ssl connect/disconnect (fetch, ovpn, etc.);
- trafficflow - allow to filter with interface lists;
- vrrp - fixed missing vrrp interfaces after upgrade (introduced in 6.36rc5 and 6.35.1);
- chr - fixed stalling services (introduced in 6.36rc6);
- dhcp-server - fixed radius framed route addition after reboot on client renew;
- lte - improved multiple same model modems identification;
- route - fixed ospf-v3 crash (introduced in 6.36rc6);
- traffic-flow - added ipfix support (RFC5101 and RFC5102);
- ipsec - fix initiator modecfg dynamic dns;
- nand - improved nand refresh feature to enhance stored data integrity;
- route - fixed ospf by handling ipv6 encoded prefixes with stray bits;
- arp - added arp-timeout option per interface;
- ntp - fixed time keeping on SXT ac, RB911L, cAP and wAP
- tunnel - added option to auto detect tunnel local-address;
- wireless-rep - fixed scan-list unset;
- firewall - added udplite, dccp, sctp connection tracking helpers;
- switch - fixed switch compact export;
- wireless - wireless-fp is discontinued, it needs to be uninstalled/disabled before upgrade;

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related MikroTik Drivers