Vantec NST-260WS3-WH Enclosure Firmware 1.1.68 Download

Posted at December 25, 2024 by PCI-DB Team

Vantec NST-260WS3-WH Enclosure Firmware 1.1.68 Description

Updating Firmware Using iOS:

- Place the *.bin file into the root path of the hard drive.
- Power off and disconnect the NST-D300WS3’s USB cable from your computer.
- Turn on the NST-D300WS3 and connect to the NST-D300WS3’s Wi-Fi signal.
- Once connected, please ensure the *.bin file is located on the root path on the hard drive.
- Click on the Settings gear icon to enter NST-D300WS3 setting and navigate to System.
- Tap on “Firmware Update” and select the *.bin file to begin. When prompted, tap Ok.
- The firmware update will proceed. Please do not turn off the NST-D300WS3 or power off your iOS device. Once the update has reached 100%, the NST-D300WS will reboot.
- You may now connect to the NST-D300WS3. Please make sure the firmware has been successfully updated by visiting the NexStar WiFi App Settings>Status.

Updating Firmware Using Android:

- Place the *.bin file into the root path of the hard drive.
- Power off and disconnect the NST-D300WS3’s USB cable from your computer.
- Turn on the NST-D300WS3 and connect to the NST-D300WS3’s Wi-Fi signal.
- Once connected, please ensure the *.bin file is located on the root path on the hard drive.
- Click on the drop down Settings icon indicated by the 3 dots to enter NST-D300WS3 setting and navigate to System.
- Tap on “Firmware Update” and select the *.bin file to begin. When prompted, tap Ok.
- The firmware update will proceed. Please do not turn off the NST-D300WS3 or power off your Android device. Once the update has reached 100%, the NST-D300WS will reboot.
- You may now connect to the NST-D300WS3. Please make sure the firmware has been successfully updated by visiting the NexStar WiFi App Settings>Status.

Updating Firmware without Software:

- Place the *.bin file into the root path of the hard drive.
- Power off and disconnect the NST-D300WS3’s USB cable from your computer.
- While holding the reset button down, turn on the NST-D300WS3.
- Continue to hold for 10 seconds and let go of the reset button.
- The hard drive LED indicator will blink and flash indicating Firmware update is in progress, please allow at least 2 minutes for the process to complete.
- Power cycle the NST-D300WS3 allowing at least 4 seconds of power off.
- You may now connect to the NST-D300WS3. Please make sure the firmware has been successfully updated by visiting the NexStar WiFi App Settings>Status.

About HDD Firmware:

Updating the HDD’s (Hard Disk Drive) firmware version can fix various problems that might occur, enhance some of the features available or add support for new ones, and improve the unit’s overall performance.

However, as this task can be very risky, applying a different firmware is recommended only when the newer version specifically resolves an issue that bothers you, or brings about changes that you can make full use of.

In addition to that, make sure you perform this task only in a steady power environment (such as the one ensured by a UPS unit).

As for the update process, due to the wide variety of HDDs and various methods provided by each manufacturer for installing a new firmware, it would be best if you carefully read and understand the installation steps.

That being said, if you consider updating the HDD to this firmware version, click the download button, and make sure you read the installation guide before initiating the upgrade. Moreover, constantly check with our website to stay up to date with the latest releases. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Vantec Drivers