MikroTik RouterOS MIPSBE Firmware 6.43 RC 3 Download

Posted at November 21, 2024 by PCI-DB Team

MikroTik RouterOS MIPSBE Firmware 6.43 RC 3 Description

What's new in 6.43rc3:

- bridge - fixed hardware offloading for MMIPS and PPC devices;
- bridge - fixed LLDP packet receiving;
- certificate - add "expires-after" parameter (CLI only);
- chr - added checksum offload support for Hyper-V installations;
- chr - added large send offload support for Hyper-V installations;
- chr - added multiqueue support on Xen installations;
- chr - added support for multiqueue feature on "virtio-net";
- chr - added virtual Receive Side Scaling support for Hyper-V installations;
- chr - do not show IRQ entries from removed devices;
- chr - fixed NIC hotplug for "virtio-net";
- chr - improved boot time for Hyper-V installations;
- crs317 - fixed link flapping when inserted S+RJ10 module without any cable;
- crs3xx - fixed failing connections through bonding in bridge;
- ike2 - use "policy-template-group" parameter when picking proposal as initiator;
- ipsec - added "responder" parameter for "mode-config" to allow multiple initiator configurations (CLI only);
- ipsec - added "src-address-list" parameter for "mode-config" that generates dynamic "src-nat" rule (CLI only);
- ipsec - added warning messages for incorrect peer configuration;
- ipsec - do not allow removal of "proposal" and "mode-config" entries that are in use;
- ipsec - separate phase1 proposal configuration from peer menu (CLI only);
- led - added "dark-mode" functionality for hAP ac and hAP ac^2 devices;
- led - improved w60g alignment trigger;
- log - show interface name on OSPF "different MTU" info log messages;
- lte - added extended LTE signal info for SIM7600 modules;
- lte - allow to send "at-chat" command over disabled LTE interface;
- lte - allow to use multiple PLS modems at the same time;
- lte - expose GPS channel for PLS modems;
- lte - fixed SIM7600 registration info;
- routerboard - allow to fill up to half of the RAM memory with files on devices with FLASH storage;
- routerboard - fixed "mode-button" support on hAP lite r2 devices;
- w60g - allow to manually set "tx-sector" value;
- w60g - fixed incorrect RSSI readings;
- w60g - show phy rate on "/interface w60g monitor" (CLI only);
- winbox - added bridge Fast Forward statistics counters;
- winbox - allow to specify "any" as wireless "access-list" interface;
- winbox - fixed "/ip dhcp-server network set dns-none" parameter;
- winbox - fixed bridge port MAC learning parameter values;
- winbox - show "Switch" menu on cAP ac devices;
- winbox - show correct "Switch" menus on CRS328-24P-4S+;
- wireless - enable all chains by default on devices without external antennas after configuration reset;
- wireless - improved compatibility with BCM chipset devices;

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related MikroTik Drivers