Integra DTR-40.2 A/V Receiver Firmware 1.10 Download

Posted at April 19, 2024 by PCI-DB Team

Integra DTR-40.2 A/V Receiver Firmware 1.10 Description

Changes:

- Improves the operation when HDMI Through is set to on
- Stabilizes the operation of Network Control

Notes:

- Make sure the AV receiver and TV are turned on.
- Never unplug or turn off the AV receiver during updating process.
- Never plug or unplug an HDMI cable during updating process.
- Never unplug the USB storage device containing the firmware file and the AC power cord during updating process.
- Do not access the AV receiver from PC during updating process.
- It will take about 30 minutes to update the firmware.
- The AV receiver will retain all your settings after update is finished.

Before you start:

- Check HDMI Control (RIHD) setting. The update may not be successful if this setting is on.
- Turn off the controller device connected via RS232C and via Ethernet network.
- Turn off Zone 2 and Zone 3.
- Stop playback of content from Internet radio, iPod,
- USB or servers, etc.

Update Procedure via USB:

- Connect a USB storage device to your PC. If there is any data in the USB storage, remove it.
- Download the firmware file and unzip it.
- Copy the extracted files to the USB storage device. Be careful not to copy the zip file.
- Remove the USB storage device from your PC and connect it to the USB port on the AV receiver/controller.
- When the AV receiver/controller has two USB ports, you can use either one.
- Make sure your AV receiver/controller and TV are turned on.
- If the AV receiver/controller is in standby mode, push [ON/STANDBY] to light up the front display.
- Select the USB input source. “Now Initializing” is displayed on the front display and then the name of the USB storage device is displayed. It will take 20 to 30 seconds to recognize the USB storage device.
- Push [RECEIVER] followed by [SETUP] on the remote controller.
- Main menu will be displayed on TV screen.
- Procedures thereafter can also be performed on the AV receiver/controller by using its SETUP, arrow, and ENTER buttons.
- Go to “Hardware Setup” menu.
- Go to “7-7. Firmware Update” menu.
- Select “Via USB” and push [ENTER].
- Select “Update” and push [ENTER].
- Updating will begin.
- As the updating progresses, the TV screen may disappear depending on the program updated. In this case, you can see the update progress on the front display of the AV receiver/controller. The TV screen will reappear when you finish the update and turn on the AV receiver/controller.
- Do not turn off the AV receiver/controller and do not remove the USB storage device during updating process.
- Message “Complete!” appears on the front display of the AV receiver, indicating that the update has been completed
- Using the [ON/STANDBY] button on the front panel, turn off the AV receiver/controller and then remove the USB storage device.
- Do not use the ON or STANDBY button on the remote controller.
- Push ON/STANDBY to turn on the AV receiver/controller.
- Congratulations!! Now you have the latest firmware on your Onkyo AV receiver/controller.

About A/V Receivers:

Each Audio-Video Receiver (A/V Receiver) is powered by a firmware version that enables all of its features and allows users to make the most of the device. Updating the firmware can bring various changes that should boost performance, such as improved compatibility with different multimedia file formats.

In order to do so, usually, you must transfer the firmware onto an empty USB storage device, connect the flash drive to the A/V Receiver, and initiate the upgrade process from the device’s setup menu.

However, this task must be carefully performed in a steady power environment, by someone who has completely read and understood all the installation steps or by a power user (recommended) – an update failure can cause your receiver's software to encounter serious malfunctions.

Therefore, if you think that this release can improve your audio-video receiver in any way, get the desired version through the available download button and apply the new firmware; if not, check with our website as often as possible so that you don’t miss the update that might improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Others Drivers