Integra DHC-80.2 A/V Receiver Firmware 1.11 Download

Posted at December 23, 2024 by PCI-DB Team

Integra DHC-80.2 A/V Receiver Firmware 1.11 Description

Changes:

- Stabilizes the operation of Network Control

Before you start:

- Check HDMI Control (RIHD) setting. The update may not be successful if this setting is on.
- Turn off the controller device connected via RS232C and via Ethernet network.
- Turn off Zone 2 and Zone 3.
- Stop playback of content from Internet radio, iPod, USB or servers, etc.
- If there is any data in the USB storage device, remove it.

Update procedure:

- Connect a USB storage device to your PC. If there is any data in the USB storage device, remove it.
- Download and unzip the firmware file.
- Copy the extracted files to the USB storage device. Be careful not to copy the zip file.
- Remove the USB storage device from your PC and connect it to the USB port on the AV receiver/controller. When the AV receiver/controller has two USB ports, you can use either one.
- Make sure the AV receiver/controller and TV are turned on.
- If the AV receiver/controller is in standby mode, press ON/STANDBY to light up the front display.
- Select the USB input source. “ Now Initializing” is displayed on the front display and then the name of the USB storage device is displayed. It will take 20 to 30 seconds to recognize the USB storage device.
- Press RECEIVER followed by SETUP on the remote controller.
- Main menu will be displayed on TV screen. Procedures thereafter can also be performed on the AV receiver/controller by using its SETUP, arrow, and ENTER buttons.
- Go to “ Hardware Setup” menu.
- Go to “ Firmware Update” menu.
- Select “via USB” and press ENTER.
- Select “Update” and press ENTER.
- Updating will begin.
- As the updating progresses, the TV screen may disappear depending on the program updated. In this case, you can see the update progress on the front display of the AV receiver/controller. The TV screen will reappear when you finish the update and turn on the AV receiver/controller.
- Do not turn off the AV receiver/controller and do not remove the USB storage device during updating process.
- Message “Complete!” appears on the front display of the AV receiver/controller, indicating that the update has been completed.
- Using ON/STANDBY on the front panel, turn off the AV receiver/controller and then remove the USB storage device.
- Do not use ON or STANDBY on the remote controller.
- Press ON/STANDBY to turn on the AV receiver/controller.
- Congratulations!! Now you have the latest firmware on the AV receiver/controller.

Precautions:

- Check the network connection before update.
- Do not touch the cable or any other device connected to the AV receiver/controller during updating process.
- Do not access the AV receiver/controller from PC during updating process.
- Do not shutdown the power of the AV receiver/controller while update.
- The storage media in the USB card reader may not work.
- If the storage device has been partitioned, each section will be treated as an independent device.
- If the USB mass storage device contains a lot of data, the AV receiver/controller may take a while to read it.
- Operation with all USB mass storage devices including the ability to power them is not guaranteed.
- Integra accepts no responsibility whatsoever for the loss or damage to data stored on a USB mass storage device when that device is used with the AV receiver/controller. Integra recommends that you back up your important music files beforehand.
- If you connect a USB hard disk drive to the USB port, Integra recommends that you use its AC adapter to power it.
- USB hubs and USB devices with hub functions are not supported. Do not connect your USB mass storage device via a USB hub.
- USB mass storage devices with security functions are not supported.

About A/V Receivers:

Each Audio-Video Receiver (A/V Receiver) is powered by a firmware version that enables all of its features and allows users to make the most of the device. Updating the firmware can bring various changes that should boost performance, such as improved compatibility with different multimedia file formats.

In order to do so, usually, you must transfer the firmware onto an empty USB storage device, connect the flash drive to the A/V Receiver, and initiate the upgrade process from the device’s setup menu.

However, this task must be carefully performed in a steady power environment, by someone who has completely read and understood all the installation steps or by a power user (recommended) – an update failure can cause your receiver's software to encounter serious malfunctions.

Therefore, if you think that this release can improve your audio-video receiver in any way, get the desired version through the available download button and apply the new firmware; if not, check with our website as often as possible so that you don’t miss the update that might improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Others Drivers