Gigabyte GA-790XTA-UD4 (rev. 1.0) Marvell RAID Utility 4.1.0.1700 Download

Posted at December 26, 2024 by PCI-DB Team

Gigabyte GA-790XTA-UD4 (rev. 1.0) Marvell RAID Utility 4.1.0.1700 Description

Specifications:

- CPU
Support for Socket AM3 processors: AMD Phenom II processor / AMD Athlon II processor
Hyper Transport Bus
5200 MT/s

- Chipset
North Bridge: AMD 790X
South Bridge: AMD SB750

- Memory
4 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory
Dual channel memory architecture
Support for DDR3 1866(OC)/1333/1066 MHz memory modules

- Audio
Realtek ALC889 codec
High Definition Audio
2/4/5.1/7.1-channel
Support for Dolby Home Theater
Support for S/PDIF In/Out
Support for CD In

- LAN
1 x Realtek 8111D chip (10/100/1000 Mbit)

- Expansion Slots
1 x PCI Express x16 slot, running at x16 (PCIEX16)
1 x PCI Express x16 slot, running at x8 (PCIEX8)
(The PCIEX16 and PCIEX8 slots conform to PCI Express 2.0 standard.)
2 x PCI Express x1 slots
3 x PCI slots

- Multi-Graphics Technology
Support for ATI CrossFireX technology

- Storage Interface
Chipset:
1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices
6 x SATA 3Gb/s connectors (SATA2_0, SATA2_1, SATA2_2, SATA2_3, SATA2_4, SATA2_5) supporting up to 6 SATA 3Gb/s devices
Support for SATA RAID 0, RAID 1, RAID 5, RAID 10, and JBOD
Marvell 9128 chip:
2 x SATA 6Gb/s connectors (GSATA3_6, GSATA3_7) supporting up to 2 SATA 6Gb/s devices
Support for SATA RAID 0 and RAID 1
SATA3 RAID 0 4x and SATA3 2x performance are maximum theoretical values. Actual performance may vary by system configuration.
SATA3 SSDs are not recommended for use in RAID 0 mode on Marvell SE9128 ports.
JMicron JMB362 chip:
2 x eSATA 3Gb/s connectors on the back panel supporting up to 2 SATA 3Gb/s devices
Support for SATA RAID 0, RAID 1, and JBOD
iTE IT8720 chip:
1 x floppy disk drive connector supporting up to 1 floppy disk drive
USBChipset:
Up to 10 USB 2.0/1.1 ports (6 on the back panel, 4 via the USB brackets connected to the internal USB headers)
NEC chip:
Up to 2 USB 3.0/2.0 ports on the back panel
USB 3.0 10x performance is a maximum theoretical value. Actual performance may vary by system configuration.

- IEEE 1394
T.I. TSB43AB23 chip
Up to 3 IEEE 1394a ports (2 on the back panel, 1 via the IEEE 1394a bracket connected to the internal IEEE 1394a header)

- Internal I/O Connectors
1 x 24-pin ATX main power connector
1 x 8-pin ATX 12V power connector
1 x floppy disk drive connector
1 x IDE connector
6 x SATA 3Gb/s connectors
2 x SATA 6Gb/s connectors
1 x CPU fan header
2 x system fan header
1 x power fan header
1 x front panel header
1 x front panel audio header
1 x CD In connector
1 x S/PDIF In header
1 x S/PDIF Out header
1 x IEEE 1394a header
2 x USB 2.0/1.1 headers
1 x serial port header
1 x clearing CMOS jumper

- Back Panel Connectors
1 x PS/2 keyboard port
1 x PS/2 mouse port
1 x optical S/PDIF Out connector
1 x coaxial S/PDIF out connector
6 x USB 2.0/1.1 ports
2 x USB 3.0/2.0 ports
2 x IEEE 1394a port
2 x eSATA 3Gb/s ports
1 x RJ-45 port
6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker Out/Line In/Line Out/Microphone)

- I/O Controller
ITE IT8720 chip

- H/W Monitoring
System voltage detection
CPU/System temperature detection
CPU/System/Power fan speed detection
CPU overheating warning
CPU/System/Power fan fail warning
CPU/System fan speed control

- BIOS
2 x 8 Mbit flash
Use of licensed AWARD BIOS
Support for DualBIOS
PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Marvell Drivers