Gigabyte GA-C1007UN (rev. 1.0) Intel Graphics Driver 6.14.10.5406 for XP64 Download

Posted at April 28, 2024 by PCI-DB Team

Gigabyte GA-C1007UN (rev. 1.0) Intel Graphics Driver 6.14.10.5406 for XP64 Description

Specifications:

- CPU
Built in with an Intel Dual-core Celeron 1007U processor (1.5 GHz)
Do not disassemble the onboard CPU/chipset and the heatsinks/fan by yourself to avoid damage to these components.
2 MB L3 cache

- Chipset
Intel NM70 Chipset

- Memory
2 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory
Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than the size of the physical memory installed.
Dual channel memory architecture
Support for DDR3 1333/1066 MHz memory modules

- Onboard Graphics
Integrated Graphics Processor:
1 x D-Sub port
1 x HDMI port, supporting a maximum resolution of 1920x1200
Support for HDMI 1.4 version.
Maximum shared memory of 1 GB

- Audio
Realtek ALC887 codec
High Definition Audio
2/4/5.1/7.1-channel
To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.

- LAN
2 x Realtek GbE LAN chips (10/100/1000 Mbit)

- Expansion Slots
1 x PCI slot

- Storage Interface
Chipset:
1 x SATA 6Gb/s connector (SATA3 0) supporting up to 1 SATA 6Gb/s device
2 x SATA 3Gb/s connectors (SATA2 1~2) supporting up to 2 SATA 3Gb/s devices
1 x eSATA 3Gb/s connector on the back panel supporting up to 1 SATA 3Gb/s device
JMicron JMB368 chip:
1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices

- USB
Chipset:
Up to 8 USB 2.0/1.1 ports (4 ports on the back panel, 4 ports available through the internal USB headers)

- Internal I/O Connectors
1 x 24-pin ATX main power connector
1 x 4-pin ATX 12V power connector
1 x IDE connector
1 x SATA 6Gb/s connector
2 x SATA 3Gb/s connectors
1 x CPU fan header
1 x system fan header
1 x front panel header
1 x front panel audio header
2 x USB 2.0/1.1 headers
1 x parallel port header
1 x serial port header
1 x Clear CMOS jumper
1 x chassis intrusion header

- Back Panel Connectors
1 x PS/2 keyboard port
1 x PS/2 mouse port
1 x D-Sub port
1 x serial port
1 x HDMI port
4 x USB 2.0/1.1 ports
1 x eSATA 3Gb/s connector
2 x RJ-45 ports
3 x audio jacks (Line In/Line Out/Microphone)

- I/O Controller
iTE I/O Controller Chip

- H/W Monitoring
System voltage detection
CPU/System temperature detection
CPU/System fan speed detection
System fan speed control
Whether the system fan speed control function is supported will depend on the system cooler you install.

- BIOS
2 x 32 Mbit flash
Use of licensed AMI EFI BIOS
Support for DualBIOS
PnP 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related INTEL Drivers