HP ProLiant MicroServer Gen8 iLO 4 Firmware 2.02 Download

Posted at December 22, 2024 by PCI-DB Team

Install Driver Automatically

Device Name	HP ProLiant MicroServer Gen8 iLO 4 Firmware 2.02
Category	Firmware
Manufacturer	HP
File Size	12.2 MB
Supported OS	Windows 2008 ,Windows Server 2012

HP ProLiant MicroServer Gen8 iLO 4 Firmware 2.02 Description

This component provides and installs an updated version of firmware for the iLO 4 Management Processor allowing for continued management support of your Server.

Enhancements:

- The following condition was added for DIMMs: "Good, Partially in Use.”
- The RIBCL Get Embedded Health has been updated for the following AMP modes: Channel Sparing, Rank Sparing, Intrasocket Mirroring, and Intersocket Mirroring.

Fixes:

- The iLO Link-Local IPv6 address is displayed during POST when iLO is using the Shared Network Port, but the Shared Network Port does not support IPv6.
- The inlet air sensor is not displayed on the temperature graph.
- The Memory page is displayed incorrectly on ProLiant DL580 Gen8 servers.
- The following message appears during POST after RBSU changes are made and the IML is cleared: iLO FW communication issue-Unable to communicate with iLO FW.
- A “repaired” message is automatically posted to the IML after a Critical Fan Event.
- Power button actions do not respond in the HP RESTful API.
- IPMI Alert Immediate (Get Alert Status) always returns an error completion code.
- Component firmware flash status is not shown at the bottom of the iLO web interface window.
- The Remote Console crashes when a URL greater than 256 bytes is mounted.
- Multiple 6064 SNMP Correctable Memory Error Trap occur when only one is expected.
- iLO RBSU incorrectly provides the Transceiver Speed Autoselect menu option when the server uses Shared Network Port mode.
- An incorrect error message is displayed when the boot order is changed by a user without the Configure iLO Settings privilege.
- The Enable Active Health System logging check box and Apply button are active when the Active Health System has been disabled in hardware by using a motherboard switch.
- Fan Blowout during POST due to a jammed rotor continues to occur when the OS is running and the rotor has been repaired.
- iLO RBSU does not correctly check user privileges.
- iLO RBSU incorrectly uses a maximum of 19 characters for user names.
- The embedded Remote Support services fails to detect an Uncorrectable memory error event.
- Cache module status is displayed for HP Dynamic Smart Array B140i Controllers.
- Storage configuration changes are not updated in iLO until the server OS is started.
- There are virtual media mounting problems when using the HP RESTful API.
- Multiple mismatched power supplies are not detected.
- The Active Health System page shows the estimated size of entire log file as Unknown.
- The iLO web interface crashes when a user browses to the Memory page.
- The Join Group button on the Administration > iLO Federation page is unavailable until the browser is refreshed.
- A 404 error occurs when the HP RESTful API is used to access any path underneath /rest/v1/systems/1/bios.

For best performance and IPv6 support, HP recommends upgrading to the latest versions of the iLO utilities:

- HPQLOCFG 1.20 (replaced CPQLOCFG)
- HP Lights-Out XML Scripting Sample 4.40 bundle
- HPONCFG 4.4.0.0
- LOCFG.PL 4.40 (included in the HP Lights-Out XML Scripting Sample bundle)
- HPLOMIG 4.40 (upgrade HPLOMIG before installing this version of iLO 4)

Networking Features supported by IPv6 in this release:

- IPv6 Static Address Assignment
- IPv6 SLAAC Address Assignment
- IPv6 Static Route Assignment
- IPv6 Static Default Gateway Entry
- DHCPv6 Stateful Address Assignment
- DHCPv6 Stateless DNS, Domain Name, and NTP Configuration
- Integrated Remote Console
- OA Single Sign-On
- HP-SIM Single Sign-On
- Web Server
- SSH Server
- SNTP Client
- DDNS Client
- RIBCL over IPv6
- SNMP
- AlertMail
- Remote Syslog
- WinDBG Support
- CPQLOCFG/HPLOMIG over an IPv6 connection
- Scriptable Virtual Media
- CLI/RIBCL Key Import over IPv6
- Authentication using LDAP and Kerberos over IPv6
- iLO Federation

Networking Features not supported by IPv6 in this release:

- IPv6 Over Shared Network Port Connections
- IPMI
- NETBIOS-WINS
- Enterprise Secure Key Manager (ESKM) Support
- Embedded Remote Support (ERS)

Upgrade Requirement:

- Users should update to this version if their system is affected by one of the documented fixes or if there is a desire to utilize any of the enhanced functionality provided by this version.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related HP Drivers