Gigabyte GA-X38T-DQ6 (rev. 1.1) SATA2 Preinstall Driver 1.17.50.2 x64 Download

Posted at December 3, 2024 by PCI-DB Team

Gigabyte GA-X38T-DQ6 (rev. 1.1) SATA2 Preinstall Driver 1.17.50.2 x64 Description

Specifications:

- CPU
Support for an Intel Core 2 Extreme processor/ Intel Core 2 Quad processor/ Intel Core 2 Duo processor/ Intel Pentium processor Extreme Edition/ Intel Pentium D processor/ Intel Pentium 4 processor Extreme Edition/ Intel Pentium 4 processor in the LGA 775 package
Support for Intel Hyper-Threading Technology
Support 1600/1333/1066/800 MHz FSB

- Chipset
Northbridge: Intel X38 Express Chipset
Southbridge: Intel ICH9R
T.I IEEE 1394 Controller
Gigabit Lan Controller
8 Channels ALC889A Audio controller

- Memory
4 x 1.5V DDR3 DIMM sockets supporting up to 8 GB of system memory
Dual channel memory architecture
Support for DDR3 1800(O.C.)/1600/1333/1066/800MHz, non ECC memory modules
Support Intel XMP Memory controller

- Audio
Realtek ALC889A codec
High Definition Audio
2/4/5.1/7.1-channel
Support for DTS (dts NEO:PC)
Support for S/PDIF In/Out
Support for CD In

- LAN
2 x Realtek 8111B chips (10/100/1000 Mbit)

- Expansion Slots
2 x PCI Express 2.0 x16 slots (The PCIE_16_1 slot supports x16; the PCIE_16_2 supports x16.)
3 x PCI Express x1 slots (share with the PCIE_16_2 slot)
2 x PCI slots

- Storage Interface
South Bridge:
6 x SATA 3Gb/s connectors (SATAII0, SATAII1, SATAII2, SATAII3, SATAII4, SATAII5) supporting up to 6 SATA 3Gb/s devices
Support for SATA RAID 0, RAID 1, RAID 5, and RAID 10
GIGABYTE SATA2 chip:
1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices
2 x SATA 3Gb/s connectors (GSATAIIA, GSATAIIB) supporting up to 2 SATA 3Gb/s devices
Support for SATA RAID 0, RAID 1, and JBOD
iTE IT8718 chip:
1 x floppy disk drive connector supporting up to 1 floppy disk drive

- IEEE 1394
T.I. TSB43AB23 chip
Up to 3 IEEE 1394a ports (2 on the back panel, 1 via the IEEE 1394a bracket connected to the internal IEEE 1394a header)

- USB
Integrated in the South Bridge
Up to 12 USB 2.0/1.1 ports (8 on the back panel, 4 via the USB brackets connected to the internal USB headers)

- Internal I/O Connectors
1 x 24-pin ATX main power connector
1 x 8-pin ATX 12V power connector
1 x 4-pin PCIe 12V power connector
1 x floppy disk drive connector
1 x IDE connector
8 x SATA 3Gb/s connectors
1 x CPU fan header
2 x system fan headers
1 x power fan header
1 x North Bridge fan header
1 x front panel header
1 x front panel audio header
1 x CD In connector
1 x S/PDIF In header
1 x S/PDIF Out header
2 x USB 2.0/1.1 headers
1 x IEEE 1394a headers
1 x parallel port header
1 x Trusted Platform Module (TPM) header
1 x serial port header
1 x power LED header
1 x chassis intrusion header

- Back Panel Connectors
1 x PS/2 keyboard port
1 x PS/2 mouse port
1 x coaxial S/PDIF Out connector
1 x optical S/PDIF Out connector
8 x USB 2.0/1.1 ports
2 x IEEE 1394a ports
2 x RJ-45 port
6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker Out/Line In/Line Out/Microphone)

- I/O Controller
iTE IT8718 chip

- H/W Monitoring
System voltage detection
CPU/System temperature detection
CPU/System/Power fan speed detection
CPU overheating warning
CPU/System/Power fan fail warning
CPU fan speed control

- BIOS
2 x 8 Mbit flash
Use of licensed AWARD BIOS
Support for Dual BIOSTM
PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related GIGABYTE Drivers