Posted at December 25, 2024 by PCI-DB Team
Install Driver AutomaticallyDevice Name | Buffalo TS5800DWR NAS Firmware 3.10 |
---|---|
Category | Hdd Ssd Nas Usb Flash |
Manufacturer | Buffalo |
File Size | 429.9 MB |
Supported OS | Windows XP ,Windows 2003 ,Windows Vista ,Windows 2008 ,Windows Vista 64 bit ,Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows Server |
- Web Service: Modified to sync with Dropbox, the online storage service offered by Dropbox Inc.
- Fixed a bug where the IP address could not be re-assigned correctly when the Ethernet cable was removed if the IP address that begin with "169.254" was assigned because the Ethernet interface has become disabled after a while since removing the Ethernet cable.
- Fixed a bug where a backup job did not start when the TeraStation was not connected to the network.
- Fixed a bug where the spare drive appeared as "Unknown Drive" in the notification email.
- Do not turn off the TeraStation until the firmware update is complete and the "finished" message is displayed.
- USB drives may not be mounted automatically after updating the firmware. To mount them, unplug and then reconnect them.
- Disconnect iSCSI volumes with the iSCSI Initiator before updating the firmware.
- Make sure the TeraStation's Ethernet frame size is set to a value smaller than that of the hub or router. Larger frame sizes may not transfer data to the TeraStation correctly.
- Updating firmware from version 2.40 or earlier to 3.10 will overwrite your current guest account settings. The guest account will be enabled and all user accounts' email addresses will be blank. Configure the guest and user account settings after this update.
- Connect the TeraStation and a computer to run the updater on the same network subnet. The subnet masks should be the same and the first three numbers of the IP addresses should be the same. The last number of the IP addresses should be different.
- Exit all applications. Also, stop or exit any firewall software.
- Extract the downloaded file and run "TSUpdater.exe". When a TeraStation is detected, an update window will open.
- If multiple TeraStations are connected to the network, select which TeraStation to update.
- Click 'Update' and enter the TeraStation's administrator password.
- Click 'OK'.
- It will take several minutes for the firmware to update. During the update process, the info LED will blink. Don't disconnect or power down the TeraStation until the update is finished.
- When the update is finished, a message will be displayed.
Upgrading the Network-Attached Storage (NAS) firmware can improve the system’s overall performance, stability, and security by adding various fixes for related issues, enhancing existing features (or adding support for new ones), or updating different applications.
Due to the high number of NAS manufacturers, as well as network storage types, installing a new firmware might not be always as easy as it appears – and not too safe either. Failing to perform a software update can cause serious malfunctions to the network storage.
So, before you even consider applying this release, carefully read the installation guide and initiate the process only when you have understood and completely familiarized yourself with all the steps.
Moreover, it would be best if you take into account using a UPS unit (Uninterruptible Power Supply) to perform this task, because no power disruption should affect the upgrade.
With all these aspects in mind, after you have read the installation guide, click the download button to apply this firmware version to your NAS. Remember to check back with our website in order to stay up to speed with the latest releases.
It is highly recommended to always use the most recent driver version available.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.
Device Type: Hdd Ssd Nas Usb Flash File Size: 129.7 MB Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows 8.1 ,Windows 8.1 64 bit ,Windows 10 ,Windows 10 64 bit ,Windows Mac
Install DriverDevice Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012
Install DriverDevice Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012
Install DriverDevice Type: Hdd Ssd Nas Usb Flash File Size: 129.7 MB Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows 8.1 ,Windows 8.1 64 bit ,Windows 10 ,Windows 10 64 bit ,Windows Mac
Install DriverDevice Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012
Install DriverDevice Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012
Install DriverDevice Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB OS Independent
Install DriverDevice Type: Hdd Ssd Nas Usb Flash File Size: 383.5 MB Windows 2K ,Windows XP ,Windows Vista ,Windows Vista 64 bit ,Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit
Install DriverDevice Type: Hdd Ssd Nas Usb Flash File Size: 129.7 MB Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows 8.1 ,Windows 8.1 64 bit ,Windows 10 ,Windows 10 64 bit ,Windows Mac
Install DriverDevice Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012
Install DriverFind Missing Drivers
Recent Devices
Recent Drivers
© 2024 PCI-DB.com - PCI Database Replacement. All rights reserved.