Gigabyte GA-H55M-USB3 (rev. 2.0) Realtek LAN Driver 7.049.0927.2011 for Windows 7 Download

Posted at November 21, 2024 by PCI-DB Team

Gigabyte GA-H55M-USB3 (rev. 2.0) Realtek LAN Driver 7.049.0927.2011 for Windows 7 Description

Specifications:

CPU
1. Support for an Intel Core i7 series processor/Intel Core i5 series processor/ Intel Core i3 series processor in the LGA1156 package
2. L3 cache varies with CPU

Chipset
1. Intel H55 Express Chipset

Memory
1. 4 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory
2. Dual channel memory architecture
3. Support for DDR3 2200+/1800/1600/1333/1066/800 MHz memory modules
4. Support for non-ECC memory modules
5. Support for Extreme Memory Profile (XMP) memory modules

Onboard Graphics
Integrated in the Chipset:
1. 1 x D-Sub port
2. 1 x DVI-D port
3. 1 x HDMI port
4. 1 x DisplayPort

Audio
1. Realtek ALC889 codec
2. High Definition Audio
3. 2/4/5.1/7.1-channel
4. Support for Dolby Home Theater
5. Support for S/PDIF In/Out
6. Support for CD In

LAN
1. 1 x RTL8111E chip (10/100/1000 Mbit)

Expansion Slots
1. 1 x PCI Express x16 slot, running at x16 (PCIEX16)
(The PCIEX16 slot conforms to PCI Express 2.0 standard.)
2. 1 x PCI Express x16 slot, running at x1 (PCIEX4_X1)
3. 2 x PCI slots

Storage Interface Chipset:
1. 5 x SATA 3Gb/s connectors (SATA2_0, SATA2_1, SATA2_2, SATA2_3, SATA2_4) supporting up to 5 SATA 3Gb/s devices
2. 1 x eSATA 3Gb/s connector on the back panel supporting up to 1 SATA 3Gb/s device

GIGABYTE SATA2 chip:
1. 1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices
2. 2 x SATA 3Gb/s connectors (GSATA2_5, GSATA2_6) supporting up to 2 SATA 3Gb/s devices
3. Support for SATA RAID 0, RAID 1, and JBOD

iTE IT8720 chip:
1. 1 x floppy disk drive connector supporting up to 1 floppy disk drive

USB Chipset:
1. Up to 12 USB 2.0/1.1 ports (6 on the back panel, 6 via the USB brackets connected to the internal USB headers)

NEC D720200F1 chip:
1. Up to 2 USB 3.0 ports on the back panel
IEEE 1394
T.I. TSB43AB23 chip

1. Up to 2 IEEE 1394a ports (1 on the back panel, 1 via the IEEE 1394a bracket connected to the internal IEEE 1394a header)

Internal I/O Connectors
1. 1 x 24-pin ATX main power connector
2. 1 x 8-pin ATX 12V power connector
3. 1 x floppy disk drive connector
4. 1 x IDE connector
5. 7 x SATA 3Gb/s connectors
6. 1 x CPU fan header
7. 1 x system fan headers
8. 1 x front panel header
9. 1 x front panel audio header
10. 1 x CD In connector
11. 1 x S/PDIF In header
12. 1 x S/PDIF Out header
13. 3 x USB 2.0/1.1 headers
14. 1 x IEEE 1394a header
15. 1 x serial port header
16. 1 x clearing CMOS jumper

Back Panel Connectors
1. 1 x PS/2 keyboard or PS/2 mouse port
2. 1 x D-Sub port
3. 1 x DVI-D port
4. 1 x optical S/PDIF Out connector
5. 1 x HDMI port
6. 1 x DisplayPort
7. 6 x USB 2.0/1.1 ports
8. 2 x USB 3.0 ports
9. 1 x IEEE 1394a port
10. 1 x eSATA 3Gb/s connector
11. 1 x RJ-45 port
12. 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/ Side Speaker Out/Line In/Line Out/Microphone)

I/O Controller
1. iTE IT8720 chip

H/W Monitoring
1. System voltage detection
2. CPU/System temperature detection
3. CPU/System/Power fan speed detection
4. CPU overheating warning
5. CPU/System/Power fan fail warning
6. CPU/System fan speed control

BIOS
1. 2 x 64 Mbit flash
2. Use of licensed AWARD BIOS
3. Support for DualBIOS
4. PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related REALTEK Drivers