Intel ir3 2208 ROC Hardware RAID Firmware 23.29.0-0016 Download

Posted at December 22, 2024 by PCI-DB Team

Intel ir3 2208 ROC Hardware RAID Firmware 23.29.0-0016 Description

Versions:

- Firmware 3.410.35-3698
- BIOS 5.47.05.0
- UEFI_Driver 0x06080502 (SIGNED)
- Hii v03.09.06.00 (SIGNED)
- WebBIOS 6.1-71-e_71-Rel
- ROMENV 1.08
- PCLI 05.07.00
- BootBlock 2.05.00.00-0010
- NVDATA 2.1406.03-0135
- BootBlockCommon 07.26.26.219
- FCODE 4.16.08.00

Changes:

- Various changes for different OEMs.
- Preventing PatrolRead from correcting the same error LBA in loop
- Foreign Import fail after controller exchange
- (Resolved)- Drives change to "foreign" state when FW is downgraded from MR 5.11 to MR 5.6/5.7/5.8/5.9
- Few un-acceptable prints in serial log.
- Extend firmware support for the new SuperCap revisions
- During the AC cycle test via SAS2208 MR card with TMMA, it will halt on cached data was lost error
- When we attempt to retrieve iMR Thunderbolt controller firmware logs using an application, we see some lines that are wrapped without starting on a new line.
- Internal Development team defect to fix build issues related to 240 Logical Drive API changes.
- Improve the Jetstress test performance.
- At boot up, if a learn is required or a learn is in progress, do not wait for the SuperCap to charge.
- Limit the number of retries when learn fails to start after firmware issues the learn command.
- Increasing SuperCap temperature above thresholds showed no Asynchronous Event Notification (AEN) or transition of Cache Policy to Write Through (WT)
- Cannot import foreign configuration.
- Foreign configuration import failure for spanned array with pinned cache
- Machine Check exception occurs during cache offload
- Montask issue in performance test.
- Increase the SuperCap learn time out value for 2GB TMM-B solution.
- Foreign configuration import failure when Virtual drives (VD) with pinned cache are present
- Firmware enables Dimmer Switch (DS3) Power Save Options.
- Requirement to implement 512e logical drives in Tbolt.
- Enable FastPath for all LSI Controllers
- If cache offload happens during a relearn, then the Firmware will halt at next boot for the learn completion.
- Add better debugging functionality for Alarm related field issues
- Start a learn even if the SuperCap is not completely charged.
- Change the cache policy of Virtual Drives(VDs) to Write Through(WT) if SuperCap temperature goes above 60 degree Celsius.
- Preventing controller reset after running several hours with ASPM(Active State Power Management) enabled
- Display the Command Descriptor Block(CDB) for timed out commands.
- RAID Ctrl. non-staggered spin-up after power saving- spin down
- To Disable the logging of event MR_EVT_PD_EMERGENCY_SPARE_COMMISSIONED_REMINDER
- HDD resume failed during dimmer switch test method.
- System crashes and OS boot issues with 2008 R2 based on 9280-16i4e controllers after one drive is failing in a RAID 5.
- IO freeze on R5 while running host IO with BGI
- Running Storcli /C0/CV show or (show all) starts a relearn on supercap issue
- Mechanism to override NVDATA Drive Activity LED setting
- Consistency Check media error handling is incorrect and causes data integrity issue
- Fix for Infinite retries of command for a particular sense code
- Change when checking if copyback can be done on a PD in a PRL11
- Patrol read is in progress even after issuing stop patrol read command through App
- At boot up, if a learn is required or a learn is in progress, do not wait for the SuperCap to charge.
- For a particular OEM, size of some 4TB drives is reported as zero
- correct when copyback (replace) for R11 can be done.
- Enable FastPath for all LSI Controllers
- SMART poll needs to issue log sense with page control set to current/ cummulative value
- Consistency Check media error handling is incorrect and causes data integrity issue
- Firmware breaks into montask if you boot with pinned cache
- HDD resume failed during dimmer switch test method.
- Mechanism to override NVDATA Drive Activity LED setting
- Cannot recover data from a recoverable media error after Patrol Read encounters recovery failure for RAID-1
- Getting Question Value mismatch when entering Controller management screen in HII
- CacheCade data loss after reboot
- (Port_Not_Required)- Montask occurs when running host i/o and parallel OOB command
- For a particular OEM, size of some 4TB drives is reported as zero
- Improve the Jetstress test performance.
- Increase the SuperCap learn time out value for 2GB TMM-B solution.
- Battery/ Memory Problems are detected and cache offload does not happen with a 2GB Memory module/ SuperCap design.
- Battery/ Memory Problems are detected and cache offload does not happen with a 2GB Memory module/ SuperCap design.
- MR 6.4:Patrol read is in progress even after issueing stop patrol read command through App
- 240VD Support: In Post Restrict to 64 VD only
- With more than 64 VD's in the configuration, number of Virtual Drives handled by BIOS message is not shown in the POST.
- OpROM- If there is boot message, BIOS won't detect > 64 VDs
- Display Warning Message when Preboot Configuration Utility are Disabled and User tries to lunch it
- AutoSelectBootLd is not working if user has OS in VD > 64
- Firmware enters faults state after a reboot on flashing firmware with IO in progress.
- Display the first 64 VDs in the POST (in the same sequence we get it from FW)
- OEM wants the battery status text in BIOS to change from "missing" to "N/A" for iMR solutions.
- VT-d/IOMMU support for iMR- Implement mechanism to allow system BIOS to put entries for iMR mem allocation into proper table
- WebBIOS of MR card hangs due to bios control mis-direct in OEM boards
- Write Caching HBA, JBOD/R0 supported TB controller with 240 SystemPD/LD support
- VT-d/IOMMU support for iMR- Implement mechanism to allow system BIOS to put entries for iMR mem allocation into proper table
- Firmware enters faults state after a reboot on flashing firmware with IO in progress.
- Display Warning Message when Preboot Configuration Utility are Disabled and User tries to lunch it
- setting deviceExposure greater than or eaual to 128 will show wrong VD handled by bios
- Implement password EFI_IFR_FLAG_CALLBACK bit requirement from UEFI spec 2.4 Errata B
- Return health status failed if we have returned device error from Start()
- Safe guard: Return health status failed if platform calls GetHealthStatus w/ NULL handle after we return intermediate status
- For OEM dont free the host memory during disconnect/unload process
- Ext/SCSI PassThru: UEFI Driver not filling direction flag correctly for Read
- DHP: Remove default value from numeric primitive that is present under suppressif
- Don't let user boot to OS until user discards dirty cache
- For OEM change memory type from EfiRuntimeServicesData to EfiMemoryMappedIO
- Code refactor effort: Hii Image buffer clean-up
- FMP GetImageInfo could result in stack corruption- Code Review Defect ID D26304
- UEFI Driver- has debug print statements during POST
- Install FMP on Controller Handle at Start() and the exception
- Write Caching HBA, JBOD/R0 supported TB controller with 240 SystemPD/LD support
- VT-d/IOMMU support for iMR- Implement mechanism to allow system BIOS to put entries for iMR mem allocation into proper table
- Remove default value from numeric primitive that is present under suppressif
- has debug print statements during POST
- For OEM change memory type from EfiRuntimeServicesData to EfiMemoryMappedIO
- Don't let user boot to OS until user discards dirty cache
- Code refactor effort: Hii Image buffer clean-up
- Initilize the buffer that we allocate to load HII and return EFI_OUT_OF_RESOURCES if allocation fails
- VT-d/IOMMU support for iMR- Implement mechanism to allow system BIOS to put entries for iMR mem allocation into proper table
- Do not go to WebBIOS due to a bad health status when WebBIOS is disabled in NVDATA.
- Do not go to WebBIOS due to a bad health status when WebBIOS is disabled in NVDATA.
- For OEM dont free the host memory during disconnect/unload process
- CPU EXCEPTION ERROR During CSIOR Stage
- CPU EXCEPTION ERROR During CSIOR Stage
- Install FMP on Controller Handle at Start() and the exception
- ATA Pass thru: Timeout is not passed correctly to FW
- FMP GetImageInfo could result in stack corruption- Code Review Defect ID D26304
- ATA Pass thru: Timeout is not passed correctly to FW
- Initilize the buffer that we allocate to load HII and return EFI_OUT_OF_RESOURCES if allocation fails
- Safe guard: Return health status failed if platform calls GetHealthStatus w/ NULL handle after we return intermediate status
- Minor Typos and consistency issues in HEFU HII help text
- Handling code collaborator Defects: SCGCQ00573222 and SCGCQ00568814
- HII 240 VD: HII fails to list the foreign configuration
- Hii- Restrict the user from creating the 65th VD.
- Consistency Check Start- remove mm/dd/yyyy from the string as the format is out of control of LSI
- Change the Step Value to 0 for all numeric to make sure for free edit instead of Incrementing and decrementing using +/-
- Handling Code Collaborator Defect: SCGCQ00573222
- Not able to create VD with 4k drives on OEM server.
- Update the string for help
- HII is showing RAID6 and RAID5 levels while creating VD when we have 2 512n drives and 1 4k Drives
- HII does not display power state of a PD
- Remove FMP installed on the controller handle in HII
- Address review comments
- Unable to set spinup drive count in HII
- Write Caching HBA, JBOD/R0 supported TB controller with 240 SystemPD/LD support
- Clone SCGCQ00556243 into the mainline
- Port 240VD change to Tbolt SCGCQ00441334
- Change the default Setting of Disk Cahce Policy from Unchanged to Disable.
- Add Mirror Join functionality- PR SCGCQ00521537
- Requirement for 512e implementation changes- PR SCGCQ00425778
- Ability to enable/disable JBOD mode in HII
- Change the wording in HII from Check Consistency to Make data consistent
- HII is gave a option to start reconstruction from any degraded RAID level to RAID 0.
- Detail Drives info shows incorrectly in BIOS- unknown characters appearing
- Enhance strings for Locked foreign config import feature
- Remove FMP installed on the controller handle in HII
- RSOD during POST after enabling SecureBoot with OEM controller installed
- HII reports wrong data under 'Eligible JBOD Drives for conversion' while converting JBOD to UG
- Unable to set spinup drive count in HII
- Not showing PD to assign as DHS to R50/ R60 VD if PD is of lesser size than largest PD in V
- After Rebuilding, DHS and Expand VD operations failed to update as per VD properties
- In HII ,Full initialization is not grayed out for R6 DIF arrays.
- Creation+ FW updation+ Scan foreign Configuration is disabled/grayed out in HII page
- change the numeric primitive's maximum from MAX_PHYSICAL_DRIVES to 0xff
- In HII ,Full initialization is not grayed out for R6 DIF arrays.
- Enhance help message for PD/VD Operation field
- After Rebuilding, DHS and Expand VD operations failed to update as per VD properties
- HII is gave a option to start reconstruction from any degraded RAID level to RAID 0.
- HII does not display power state of a PD
- In HII Create VD option is enabled when resconstruction is in progress (on partial VD)
- RSOD during POST after enabling SecureBoot with OEM controller installed
- Consistency Check Start- remove mm/dd/yyyy from the string as the format is out of control of LSI
- HII reports wrong data under 'Eligible JBOD Drives for conversion' while converting JBOD to UG
- When Controller is in Safe Mode don't remove UCM formset
- change the numeric primitive's maximum from MAX_PHYSICAL_DRIVES to 0xff
- Minor Typos and consistency issues in HEFU HII help text
- HII is showing RAID levels, irrespective of drives to configure a new RAID level.
- "Make Unconfigured good" option missing in HII even if JBOD's are present in the config
- creation in HII is showing GB
- HII is showing RAID6 and RAID5 levels while creating VD when we have 2 512n drives and 1 4k Drives
- "Make Unconfigured good" option missing in HII even if JBOD's are present in the config
- Not able to create VD with 4k drives on intel wildcat server.
- HII is not displaying the cachecade 512GB warning message
- Enhance help message for PD/VD Operation field
- HII is not displaying the cachecade 512GB warning message
- TB creation in HII is showing GB
- HII is showing RAID levels, irrespective of drives to configure a new RAID level.
- Call UninstallStoreLib when we call StopControllerHiiImpl function

This download is valid for the products listed below:

- Intel Integrated RAID Module RMS25CB040
- Intel Integrated RAID Module RMS25CB080
- Intel Integrated RAID Module RMS25PB040
- Intel Integrated RAID Module RMS25PB080
- Intel Integrated RAID Module RMT3CB080
- Intel Integrated RAID Module RMT3PB080
- Intel RAID Controller RS25AB080
- Intel RAID Controller RS25DB080
- Intel RAID Controller RS25NB008
- Intel RAID Controller RS25SB008

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Intel Drivers