Gigabyte GA-P55-UD4P (rev. 1.0) SATA2 Preinstall Driver 1.17.59.0 x86 Download

Posted at December 18, 2024 by PCI-DB Team

Gigabyte GA-P55-UD4P (rev. 1.0) SATA2 Preinstall Driver 1.17.59.0 x86 Description

Specifications:

CPU
1. Support for an Intel Core i7 series processor/Intel Core i5 series processor in the LGA1156 package
2. L3 cache varies with CPU

Chipset
1. Intel P55 Express Chipset

Memory
1. 4 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory
2. Dual channel memory architecture
3. Support for DDR3 2200/1600/1333/1066/800 MHz memory modules
4. Support for non-ECC memory modules
5. Support for Extreme Memory Profile (XMP) memory modules

Audio
1. Realtek ALC889A codec
2. High Definition Audio
3. 2/4/5.1/7.1-channel
4. Support for Dolby Home Theater
5. Support for S/PDIF In/Out
6. Support for CD In

LAN
1. 2 x RTL8111D chips (10/100/1000 Mbit)
2. Support for Teaming
3. Support for Smart Dual LAN

Expansion Slots
1. 1 x PCI Express x16 slot, running at x16 (PCIEX16)
2. 1 x PCI Express x16 slot, running at x8 (PCIEX8) (The PCIEX16 and PCIEX8 slots conforms to PCI Express 2.0 standard.)
3. 3 x PCI Express x1 slots
4. 2 x PCI slots

Multi-Graphics Technology
1. Support for ATI CrossFireX/NVIDIA SLI technology

Storage Interface
Intel P55 Express Chipset:
1. 6 x SATA 3Gb/s connectors (SATA2_0, SATA2_1, SATA2_2, SATA2_3, SATA2_4, SATA2_5) supporting up to 6 SATA 3Gb/s devices
2. Support for SATA RAID 0, RAID 1, RAID 5, and RAID 10

GIGABYTE SATA2 chip:
1. 1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices
2. 2 x SATA 3Gb/s connectors (GSATA2_0, GSATA2_1) supporting up to 2 SATA 3Gb/s devices
3. Support for SATA RAID 0, RAID 1, and JBOD

JMB362 SATA2 chip:
1. 2 x eSATA 3Gb/s connectors on the back panel supporting up to 2 SATA 3Gb/s devices
2. Support for SATA RAID 0, RAID 1, and JBOD

iTE IT8720 chip:
1. 1 x floppy disk drive connector supporting up to 1 floppy disk drive

USB
1. Integrated in the Chipset
2. Up to 14 USB 2.0/1.1 ports (10 on the back panel, 4 via the USB brackets connected to the internal USB headers)

IEEE 1394
1. T.I. TSB43AB23 chip
2. Up to 3 IEEE 1394a ports (2 on the back panel, 1 via the IEEE 1394a bracket connected to the internal IEEE 1394a header)

Internal I/O Connectors
1. 1 x 24-pin ATX main power connector
2. 1 x 8-pin ATX 12V power connector
3. 1 x floppy disk drive connector
4. 1 x IDE connector
5. 8 x SATA 3Gb/s connectors
6. 1 x CPU fan header
7. 2 x system fan headers
8. 1 x power fan header
9. 1 x PCH chip fan header
10. 1 x front panel header
11. 1 x front panel audio header
12. 1 x CD In connector
13. 1 x S/PDIF In header
14. 1 x S/PDIF Out header
15. 2 x USB 2.0/1.1 headers
16. 1 x IEEE 1394a header
17. 1 x serial port header
18. 1 x parallel port header
19. 1 x clearing CMOS jumper

Back Panel Connectors
1. 1 x PS/2 keyboard or PS/2 mouse port
2. 1 x coaxial S/PDIF Out connector
3. 1 x optical S/PDIF Out connector
4. 2 x IEEE 1394a ports
5. 10 x USB 2.0/1.1 ports
6. 2 x eSATA 3Gb/s ports
7. 2 x RJ-45 ports
8. 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/ Side Speaker Out/Line In/Line Out/Microphone)

I/O Controller
1. iTE IT8720 chip

H/W Monitoring
1. System voltage detection
2. CPU/System temperature detection
3. CPU/System/Power fan speed detection
4. CPU overheating warning
5. CPU/System/Power fan fail warning
6. CPU/System fan speed control

BIOS
1. 2 x 16 Mbit flash
2. Use of licensed AWARD BIOS
3. Support for DualBIOS
4. PnP 1.0a, DMI 2.0, SM BIOS 2.4, ACPI 1.0b

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related GIGABYTE Drivers