Gigabyte GA-X99-UD7 WIFI (rev. 1.0) Intel Chipset Driver 10.0.20 Download

Posted at November 17, 2024 by PCI-DB Team

Gigabyte GA-X99-UD7 WIFI (rev. 1.0) Intel Chipset Driver 10.0.20 Description

Specifications:

CPU:
- Support for Intel Core i7 processors in the LGA2011-3 package
- L3 cache varies with CPU

Chipset:

- Intel X99 Express Chipset

Memory:

- 8 x DDR4 DIMM sockets supporting up to 64 GB of system memory
- 4 channel memory architecture
- Support for DDR4 3000(O.C.) / 2800(O.C.) / 2666(O.C.) / 2400(O.C.) / 2133 MHz memory modules
- Support for non-ECC memory modules
- Support for Extreme Memory Profile (XMP) memory modules
- Support for RDIMM 1Rx8 memory modules (operate in non-ECC mode)

Audio:

- Realtek ALC1150 codec
- High Definition Audio
- 2/4/5.1/7.1-channel
- Support for S/PDIF Out

LAN:

- 2 x Intel GbE LAN chips (10/100/1000 Mbit)

Wireless Communication module:

- Wi-Fi 802.11 a/b/g/n/ac, supporting 2.4/5 GHz Dual-Band
- Bluetooth 4.0, 3.0+HS, 2.1+EDR
- Support for 11ac wireless standard and up to 867 Mbps data rate

Expansion Slots:

- 2 x PCI Express x16 slots, running at x16 (PCIE_1, PCIE_2)
- 2 x PCI Express x16 slots, running at x8 (PCIE_3, PCIE_4)
- 3 x PCI Express x1 slots
- 1 x M.2 Socket 1 connector for the wireless communication module (M2_WIFI)

Multi-Graphics Technology:

- Support for 4-Way/3-Way/2-Way AMD CrossFire/NVIDIA SLI technology

Storage Interface:

- 1 x M.2 PCIe connector
- 1 x SATA Express connector
- 6 x SATA 6Gb/s connectors (SATA3 0~5)
- Support for RAID 0, RAID 1, RAID 5, and RAID 10
- 4 x SATA 6Gb/s connectors (sSATA3 0~3), supporting IDE and AHCI modes only (An operating system installed on the SATA3 0~5 connectors cannot be used on the sSATA3 0~3 connectors.)

USB:

- 4 x USB 3.0/2.0 ports (available through the internal USB headers)
- 6 x USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through the internal USB headers)
- Chipset + 2 Renesas uPD720210 USB 3.0 Hubs:
- 8 x USB 3.0/2.0 ports on the back panel

Internal I/O Connectors:

- 1 x 24-pin ATX main power connector
- 1 x 8-pin ATX 12V power connector
- 1 x PCIe power connector
- 1 x SATA Express connector
- 10 x SATA 6Gb/s connectors
- 1 x M.2 Socket 3 connector
- 1 x CPU fan header
- 1 x water cooling fan header (CPU_OPT)
- 3 x system fan headers
- 1 x heatsink LED power connector
- 1 x I/O shield audio LED power connector
- 1 x front panel header
- 1 x front panel audio header
- 2 x USB 3.0/2.0 headers
- 2 x USB 2.0/1.1 headers
- 1 x Thunderbolt add-in card connector
- 1 x Clear CMOS jumper
- 1 x power button
- 1 x reset button
- 1 x Clear CMOS button
- 1 x Direct to BIOS button
- 2 x BIOS switches
- Voltage Measurement Points

Back Panel Connectors:

- 1 x PS/2 keyboard/mouse port
- 1 x CPU overclocking button
- 1 x Fast Boot button
- 1 x Clear CMOS button
- 8 x USB 3.0/2.0 ports
- 2 x USB 2.0/1.1 ports
- 2 x RJ-45 ports
- 2 x SMA antenna connectors (2T2R)
- 1 x optical S/PDIF Out connector
- 5 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Line In, Line Out, Mic In)

I/O Controller:

- iTE I/O Controller Chip

H/W Monitoring:

- System voltage detection
- CPU/System/Chipset temperature detection
- CPU/CPU OPT/System fan speed detection
- CPU/System/Chipset overheating warning
- CPU/CPU OPT/System fan fail warning
- CPU/CPU OPT/System fan speed control

Form Factor:

- E-ATX Form Factor: 30.5cm x 25.9cm

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Intel Drivers