Gigabyte GA-B75N (rev. 1.0) Intel Display Driver 6.14.10.5406 for XP64 Download

Posted at December 22, 2024 by PCI-DB Team

Gigabyte GA-B75N (rev. 1.0) Intel Display Driver 6.14.10.5406 for XP64 Description

Specifications:

- CPU
Support for Intel Core i7 processors/Intel Core i5 processors/ Intel Core i3 processors/Intel Pentium processors/Intel Celeron processors in the LGA1155 package
L3 cache varies with CPU

- Chipset
Intel B75 Express Chipset

- Memory
2 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory
Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than the size of the physical memory installed.
Dual channel memory architecture
Support for DDR3 1600/1333/1066/800 MHz memory modules
To support DDR3 1600 MHz, you must install an Intel 22nm (Ivy Bridge) CPU.
Support for non-ECC memory modules
Support for Extreme Memory Profile (XMP) memory modules

- Onboard Graphics
Integrated Graphics Processor:
1 x DVI-I port, supporting a maximum resolution of 1920x1200
2 x HDMI ports, supporting a maximum resolution of 1920x1200

- Audio
Realtek ALC892 codec
High Definition Audio
2/4/5.1/7.1-channel
Support for S/PDIF Out

- LAN
2 x Realtek GbE LAN chips (10/100/1000 Mbit)

- Expansion Slots
1 x PCI Express x16 slot, running at x16
(The PCIEX16 slot conforms to PCI Express 3.0 standard.)
Whether PCI Express 3.0 is supported depends on CPU and graphics card compatibility.

- Storage Interface
Chipset:
1 x SATA 6Gb/s connector (SATA3 0) supporting up to 1 SATA 6Gb/s device
3 x SATA 3Gb/s connectors (SATA2 1/2/3) supporting up to 3 SATA 3Gb/s devices

- USB
Chipset:
Up to 4 USB 3.0/2.0 ports (2 ports on the back panel, 2 ports available through the internal USB header)
Up to 6 USB 2.0/1.1 ports (4 ports on the back panel, 2 ports available through the internal USB header)

- Internal I/O Connectors
1 x 24-pin ATX main power connector
1 x 4-pin ATX 12V power connector
1 x serial port header
1 x SATA 6Gb/s connector
3 x SATA 3Gb/s connectors
1 x USB 3.0/2.0 header
1 x USB 2.0/1.1 header
1 x CPU fan header
1 x system fan header
1 x front panel header
1 x front panel audio header
1 x S/PDIF Out header
1 x Clear CMOS jumper

- Back Panel Connectors
1 x PS/2 keyboard/mouse port
2 x HDMI ports
1 x DVI-I port
2 x USB 3.0/2.0 ports
4 x USB 2.0/1.1 ports
2 x RJ-45 ports
1 x optical S/PDIF Out connector
5 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Line In, Line Out, Mic In)

- I/O Controller
iTE I/O Controller Chip

- H/W Monitoring
System voltage detection
CPU/System temperature detection
CPU/System fan speed detection
CPU fan speed control
Whether the CPU fan speed control function is supported will depend on the CPU cooler you install.

- BIOS
2 x 64 Mbit flash
Use of licensed AMI EFI BIOS
Support for DualBIOS
PnP 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a

- Form Factor
Mini-ITX Form Factor; 17.0cm x 17.0cm

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related INTEL Drivers