PCI-DB.com
  1. Driver
  2. Hdd Ssd Nas Usb Flash
  3. Buffalo TS3410RN NAS Firmware 3.50

Buffalo TS3410RN NAS Firmware 3.50 Download

Posted at December 25, 2024 by PCI-DB Team

Install Driver Automatically
Device NameBuffalo TS3410RN NAS Firmware 3.50
CategoryHdd Ssd Nas Usb Flash
ManufacturerBuffalo
File Size449.8 MB
Supported OSWindows 7 ,Windows 7 64 bit ,Windows 8.1 ,Windows 8.1 64 bit ,Windows 10 ,Windows 10 64 bit

Buffalo TS3410RN NAS Firmware 3.50 Description

Added and Modified Features

- [Data Protection]: When bad blocks on the SSD drives exceed an unrecoverable amount on the TS5210DF series TeraStations, the unit now enters data protection mode and the data area becomes read-only. For more detailed information, refer to the user manual of your TeraStation.
- [SSD]: Improved the condition to reach the guaranteed write capacity (TBW) for the drive on the TS5210DF series TeraStations.

Bug Fixes

- [iSCSI]: Fixed a bug where a drive could not be detected if an iSCSI volume was created on the drive that isn’t being used as part of a RAID array while using the “Block I/O” option for “Backstore”.
- [Replication]: Fixed a bug where the same shared folder could be configured as a replication target for multiple replication tasks.
- [Replication]: Fixed a bug where the root shared folder could be configured as a replication target if a subfolder on its shared folder was configured as a replication source.
- [Logs]: Fixed a bug where a link to logs that was created in the shared folder could not be deleted even when the setting was disabled.
- [Settings]: Fixed minor bugs.

Caution:

- Please consult your local technical support representative if you experience any problems caused by this firmware update.
- Do not turn the unit off until the update is finished. It will take several minutes. You will receive a message when the update is finished.
- USB drives are not mounted automatically after a firmware update. To mount them, unplug and then reconnect them.

How to Use the Updater:

1. Connect the TeraStation properly and configure the TeraStation and a computer to run the updater on the same network subnet. The subnet masks should be the same and the first three numbers of the IP addresses should be the same. The last number of the IP addresses should be different.
For example, if the IP address and subnet mask of the computer are
" 192.168.0.10 , 255.255.255.0 "
and the IP address and subnet mask of the TeraStation are
" 192.168.1.150 , 255.255.255.0 "
then the updater will _not_ work properly.
In this case, reconfigure the TeraStation's IP address and subnet mask to
" 192.168.0.150 , 255.255.255.0 ".
Then they will be on the same subnet and the updater will work properly.
2. Close all applications. Also, stop or exit any firewall software.
3. Extract the downloaded file and run "TSUpdater.exe". When a TeraStation is detected, an update window will open.
4. Select the TeraStation to update if multiple TeraStation are connected.
5. Click "Update" and enter the TeraStation's admin password.
6. Click "OK".
7. Transferring and updating the firmware will start. Wait until it finishes. The info LED will blink during the update.
8. When the update finishes, a message will be displayed.

About Network-Attached Storage Updates:

Upgrading the Network-Attached Storage (NAS) firmware can improve the system's overall performance, stability, and security by adding various fixes for related issues, enhancing existing features (or adding support for new ones), or updating different applications.

Due to the high number of NAS manufacturers, as well as network storage types, installing a new firmware might not be always as easy as it appears – and not too safe either. Failing to perform a software update can cause serious malfunctions to the network storage.

So, before you even consider applying this release, carefully read the installation guide and initiate the process only when you have understood and completely familiarized yourself with all the steps.

Moreover, it would be best if you take into account using a UPS unit (Uninterruptible Power Supply) to perform this task, because no power disruption should affect the upgrade.

With all these aspects in mind, after you have read the installation guide, click the download button to apply this firmware version to your NAS. Remember to check back with our website in order to stay up to speed with the latest releases.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Buffalo Drivers

Buffalo TS-8VHL/R6 NAS Firmware Update 1.15

Device Type: Hdd Ssd Nas Usb Flash File Size: 383.5 MB Windows 2K ,Windows XP ,Windows Vista ,Windows Vista 64 bit ,Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit

Install Driver

Buffalo WS5400DN2 WSS Firmware 2.90

Device Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012

Install Driver

Buffalo LS520DE NAS Firmware 4.30

Device Type: Hdd Ssd Nas Usb Flash File Size: 129.7 MB Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows 8.1 ,Windows 8.1 64 bit ,Windows 10 ,Windows 10 64 bit ,Windows Mac

Install Driver

Buffalo WS5600DN2 WSS Firmware 2.90

Device Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012

Install Driver

Buffalo LS510D NAS Firmware 4.30

Device Type: Hdd Ssd Nas Usb Flash File Size: 129.7 MB Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows 8.1 ,Windows 8.1 64 bit ,Windows 10 ,Windows 10 64 bit ,Windows Mac

Install Driver

Buffalo LS520D NAS Firmware 4.30

Device Type: Hdd Ssd Nas Usb Flash File Size: 129.7 MB Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows 8.1 ,Windows 8.1 64 bit ,Windows 10 ,Windows 10 64 bit ,Windows Mac

Install Driver

Buffalo WS5400RN2 WSS Firmware 2.90

Device Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012

Install Driver

Buffalo WS5600DR2 WSS Firmware 2.90

Device Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012

Install Driver

Buffalo WS5200DN2 WSS Firmware 2.90

Device Type: Hdd Ssd Nas Usb Flash File Size: 6.7 MB Windows Server 2012

Install Driver

Find Missing Drivers

© 2024 PCI-DB.com - PCI Database Replacement. All rights reserved.