Intel iMR 3008 ROC Hardware RAID Firmware 24.3.0-0054 Download

Posted at December 21, 2024 by PCI-DB Team

Intel iMR 3008 ROC Hardware RAID Firmware 24.3.0-0054 Description

Firmware - 4.230.31-3587

SCGCQ00625524 - When we attempt to retrieve iMR Thunderbolt controller firmware logs using an application, we see some lines that are wrapped without starting on a new line.
SCGCQ00695317 - Serial prints getting jumbled up due to print message inside spurious interrupt handler.
SCGCQ00675262 - Data Corruption is taking place on Windows OS installed on top of ESX 5.5 U1 OS.
SCGCQ00665475 - ONFI: To properly handle the OCR case with RESET Status Register.
SCGCQ00677803 - Cache offload failure with pinned cache on R5 VD
SCGCQ00674392 - Updated long term WA for PPC errata number 46
SCGCQ00568080 - Defect Fix for VPD and inquiry callback issues in DISM
SCGCQ00568134 - Patrol read will not start on any VD after a PR is started, suspended and VD is deleted
SCGCQ00569895 - Defect Fix for Command gets retried infinitely times when drive responds with 0B/47/03 always
SCGCQ00572662 - FW failure during read on 3PD R5 with 1000 CME with skip count 2
SCGCQ00574276 - FW breaks if wrong security key is entered
SCGCQ00580162 - Only 1mb crash dump is getting generated of fw fault
SCGCQ00580847 - not enough bs found during double Dip power cycle Test
SCGCQ00586163 - cache restore failure message displayed through cache restore was successful
SCGCQ00588173 - Routines to inject bit error in NF and ecc error in DDR for ONFI
SCGCQ00588185 - Mismatch in LD id and target ID during set/reset boot device
SCGCQ00589365 - on breaking the multipath in loop while drives are spinning up will result in montask
SCGCQ00589728 - FW hangs while creating 64 VDs on the controller with SLES11 SP2
SCGCQ00592996 - While running reconstruction from R1 to 4 drive PRL11 with IO,FW hits to MonTask: line 1270 in file ../../raid/1078dm
SCGCQ00593776 - SMART poll needs to issue log sense with page control set to current/ cummulative value
SCGCQ00602556 - Static analysis tool defects
SCGCQ00602665 - Static analysis tool defect
SCGCQ00602726 - Static Analysis Tool defects
SCGCQ00602855 - Static analysis tool defect
SCGCQ00603306 - static analysis tool defects resolution
SCGCQ00603564 - added support for debug queue
SCGCQ00603779 - Not getting "Clear ldbm badblocks" options on VD
SCGCQ00611275 - FW goes to kill adaptor to handle partial copy of crash_dump
SCGCQ00612927 - Montask in divert.c seen when injecting 64K consecutive errors on R0 VD, Patrol Read running in background.
SCGCQ00614455 - Static analysis tool defects
SCGCQ00625843 - PR Progress event is not generated for 1TB/3TB SATA drive
SCGCQ00634578 - Defect fix for kernel panic with iMR Fury with Freebsd driver
SCGCQ00636748 - Running Storcli /C0/CV show or (show all) starts a relearn on supercap issue
SCGCQ00451219 - Defect Fix for Online DIF drives are getting punctured after PI enabled R5 VDs are offlined with pinned cache
SCGCQ00574071 - md5sum mismatch seen on a copied file from R5 VD with CME
SCGCQ00574277 - Power removal of enclosure FW hits to MonTask: line 4056 in file ../../bbu/onfiBBM.c
SCGCQ00586190 - Fix GNU make file compilation
SCGCQ00586341 - Crash Dump Error Handling
SCGCQ00605227 - When OS on VD ,after collecting crash dump file system becomes readable
SCGCQ00606571 - Physical drives go to power save mode just after restarting the server
SCGCQ00610881 - storcli and CtrlR still show new PD information as 4K sector after replacing a 4K sector drive with a 512 sector drive
SCGCQ00630075 - Unexpected power state change
SCGCQ00631492 - Media error on Last sector of stripe isn't added to LDBBM list
SCGCQ00524842 - CME logic using overlaid fields in c->rec
SCGCQ00568655 - defect fix for Compilation issue
SCGCQ00575006 - Too many unexpected sense AEN raised by CC during CME recovery on R5
SCGCQ00593295 - Not able import foreign configuration immediately after breaking the mirror.
SCGCQ00602561 - Static Analysis Tool defects
SCGCQ00563498 - FW should not try to boot iMR mode without informing host if ECC error happens when OS is running.
SCGCQ00577680 - spin up tracker dequeue is not handled for case in which TUR error happens even after MAX retries
SCGCQ00603086 - Kill adapter is seen while performing CME recovery during Write operation.
SCGCQ00466289 - PDs more than 32 which has configuration, is reporting as JBODs after importing from MR to IMR
SCGCQ00546691 - hostCmdSortingWrites is not updated when VD policy changes(WT/WB)
SCGCQ00576138 - The restore successful and unsuccessful prints to be handled properly
SCGCQ00560474 - code review change implemented
SCGCQ00531118 - Changes to support PD IO history
SCGCQ00564339 - Enable break mirror support
SCGCQ00574801 - Implemented Fix to Problem [PDs more than 32 which has configuration, is reporting as JBODs after importing from MR to IMR]
SCGCQ00577793 - Moved divert code from iopath region to save memory
SCGCQ00621767 - Update Ptolemy VPD and GasGauge with COL settings for a OEM
SCGCQ00624326 - Disable sgpioSmpPresenceDetect for OEM
SCGCQ00625006 - Show valid ROC temperature
SCGCQ00625044 - Change SES Green/Amber LED behavior
SCGCQ00567706 - Extended LDBBM table to hold more bad block entries ( SCGCQ00295621); with relevant increase in divert nodes.
SCGCQ00588208 - Adding test routine for the bad block loop test for PR SCGCQ00423195
SCGCQ00563795 - Modify MR fw to eliminate four second window where drive swap is not recognized.
SCGCQ00564166 - Single image support for ONFI
SCGCQ00455360 - Implement CME solution for "Do not allow 3 minute timer to expire forcing driver to kill fw on CME/disk timeout/etc.
SCGCQ00563486 - Make MR to iMR migration generic on TMM fault
SCGCQ00562733 - Support for DIS feature in dual image
SCGCQ00530866 - command storclif /c1 start diag duration=0 causes controller card to montask.
SCGCQ00564367 - BGI operation still running on RAID0 VD even after PI protection disabled
SCGCQ00566951 - LED Blink operation doesn't stop after VD deletion
SCGCQ00579929 - SGPIO functionality is not working when only cable A is connected
SCGCQ00579931 - Potential null pointer dereference
SCGCQ00614997 - Physical drives go to power save mode just after restarting the server
SCGCQ00614998 - Physical drives go to power save mode just after restarting the server
SCGCQ00615001 - Montask in divert.c seen when injecting 64K consecutive errors on R0 VD, Patrol Read running in background.
SCGCQ00617621 - cache restore failure message displayed through cache restore was successful
SCGCQ00620166 - RAID configured on PD been erased with Normal or Thorough will lost after system reboot/reset
SCGCQ00620168 - RAID configured on PD been erased with Normal or Thorough will lost after system reboot/reset
SCGCQ00620169 - RAID configured on PD been erased with Normal or Thorough will lost after system reboot/reset
SCGCQ00621785 - CME handling of Invader
SCGCQ00622709 - storcli and CtrlR still show new PD information as 4K sector after replacing a 4K sector drive with a 512 sector drive
SCGCQ00624531 - Cache policy of Virtual Drives(VD) does not change to Write Through(WT) mode even after detecting a bad supercap.
SCGCQ00631230 - SSD causes system to hang at POST
SCGCQ00631232 - Behavior change when FW hit fault code 0x81 (uncorrectable ECC error)
SCGCQ00631474 - Power removal of enclosure FW hits to MonTask: line 4056 in file ../../bbu/onfiBBM.c
SCGCQ00631478 - Adding 2GB DDR and 4GB Flash combination support for Single Image Write.
SCGCQ00637535 - FW hits MonTask: line 1143 in file ../../raid/pd.c on starting VD erase in standard mode.
SCGCQ00638312 - FW crash while launching Ctrl+R
SCGCQ00640126 - 9240-4i is not getting required memory resources on boot, on Linux it waits 5 minutes, resets the
SCGCQ00640469 - Running Storcli /C0/CV show or (show all) starts a relearn on supercap issue
SCGCQ00640470 - L2/L3 cache error on H330 MM & H330 MB on reboot
SCGCQ00643455 - Defect fix for kernel panic with iMR Fury with Freebsd driver
SCGCQ00643524 - Defect fix for kernel panic with iMR Fury with Freebsd driver
SCGCQ00643526 - 9240-4i is not getting required memory resources on boot, on Linux it waits 5 minutes, resets the
SCGCQ00658583 - Work Around for PPC 476 Errata number 46 in MR Firmware
SCGCQ00658585 - Work Around for PPC 476 Errata number 46 in iMR Firmware
SCGCQ00495877 - disableBatteryWarning should not be reset if changed by user
SCGCQ00552416 - firmware 25.2.0-0013 causes the SEP to not be seen on x4 Equinox
SCGCQ00555332 - Transparent Learn Cycle does not kick off and RSOC (Relative State Of Charge) eventually goes down to 0%.
SCGCQ00559322 - EEprom CRC error is detected when WebBIOS is running
SCGCQ00579928 - AdpDiags does not fail when the SAS link is down
SCGCQ00588880 - HDD resume failed during dimmer switch test method.
SCGCQ00630382 - Add MaintainPdFailHistory clear function
SCGCQ00631340 - Single image support for ONFI
SCGCQ00637536 - FW hits MonTask: line 1143 in file ../../raid/pd.c on starting VD erase in standard mode.
SCGCQ00675820 - Updated long term WA for PPC errata number 46
SCGCQ00504394 - For a particular OEM, size of some 4TB drives is reported as zero
SCGCQ00523966 - Rebuild failed event is not seen when rebuild fails due to LDBBM and SBBM tables getting full (puncturing disabled)
SCGCQ00552446 - Implement I2C Slave Address for Sideband Management
SCGCQ00563282 - OEM hi-temp warning not being displayed
SCGCQ00570249 - OEM SGPIO support not working
SCGCQ00574969 - Retention test failure during stress test
SCGCQ00596686 - cntr-R fails to show correct PD sector size once PD's swapped to same slot 512B PD with 512e PD type
SCGCQ00621783 - Assertion failure (not enough BS found) in double DIP power cycle test case
SCGCQ00646386 - DIS mismatch while running system reboot script with dirty data in DDR
SCGCQ00366011 - FW goes to montask at cache offload.
SCGCQ00498741 - Megamon during Injecting errors to VD with 512e PDs on iMR controller
SCGCQ00526627 - Faulty protocol used for changing the Disk Write Cache Policy
SCGCQ00530868 - "OOB:Got DCMD, but FW is not ready " messages are flooding in tty log during OCR .
SCGCQ00553197 - Prevent overtemp warnings while charging between 45C and 50C
SCGCQ00560388 - adapterOperations.alarmControl is being set to 1 even if controller does not have alarm on board
SCGCQ00567378 - CLI Reporting of TMM VPD
SCGCQ00556598 - megacli reports battery pack is missing on hot insertion
SCGCQ00679766 - MonTask: line 4699 in file ../../raid/ld.c seen on iMR FW during boot to OS with R0 and PRL11 VD
SCGCQ00550612 - Do not print VPD86 errors for BP/expander
SCGCQ00552415 - Modify WCE bit for improved Linux performance
SCGCQ00560393 - When attempting to secure LD during RLM, receive option to secure LD, LD not secured (message incorrect/misleading.)
SCGCQ00558037 - Megamon issue when disabling the drive security on a MR controller with spun down FDE drives.
SCGCQ00560476 - Unable to open "Set Patrol Read Properties" in MSM with 2008-iMR

BIOS - 6.17.04.0

SCGCQ00579962 - Initialize deviceExposure with MAX_INT13DISKS instead of 0xFF
SCGCQ00572939 - Make sure all the make file adheres to the latest binary names.
SCGCQ00559095 - Provide an option to limit the max number of INT 13h devices presented to system BIOS

UEFI_Driver - 0x06060A01 (Signed)

SCGCQ00618669 - StartHiiBackEnd() has Print statement with %g
SCGCQ00578194 - UEFI Driver should calculate checksum before setting bios data (MR_BIOS_DATA)
SCGCQ00601851 - System hang when we press F1 on second time when we are in HII form
SCGCQ00628627 - UEFI Driver- has debug print statements during POST
SCGCQ00589148 - Diskpart EFI utility can't create partition on a JBOD
SCGCQ00526851 - Support EFI_FIRMWARE_MANAGEMENT_PROTOCOL for controller firmware upgrade.
SCGCQ00579837 - UEFI Driver should calculate checksum before setting bios data (MR_BIOS_DATA)
SCGCQ00606367 - UEFI Driver returns EFI_NOT_FOUND when platform passes valid Target for ExtSPT.BuildDevicePath()
SCGCQ00644856 - Install FMP on Controller Handle at Start() and the exception
SCGCQ00644859 - FMP GetImageInfo could result in stack corruption - Code Review Defect ID D26304
SCGCQ00580313 - User can't access RAID HII in UEFI mode after removing a HDD

Hii - 03.07.12.01 (Signed)

SCGCQ00579816 - HII\EKM-LKM without reboot should show proper message
SCGCQ00594011 - Without selecting any drives I am seeing the previous config VD size.
SCGCQ00609737 - Configuration Restore is not working
SCGCQ00618674 - StartHiiImpl() WriteToLogger uses %g and EFIHiiDriverEntryPoint() Print statement uses %g for displaying EFI status
SCGCQ00521488 - Getting error message when we suspend Patrol read operation through HII browser
SCGCQ00565876 - Remove duplicated strings from the UNI FIle
SCGCQ00571353 - Allow user to select RAID level when controller has other VD + error handling
SCGCQ00573871 - fixing code review defects (AIM version + UCM GUID + deallocation)
SCGCQ00614027 - Firmware updation fails in OEM machine
SCGCQ00615221 - Form UF003 prints error messages (use WriteToLogger to log these debug messages)
SCGCQ00617617 - FWMgmt Prtocol:<config ID="LSIMegaRAIDConfigurationTool"> has no "versionid" info.
SCGCQ00565088 - Help content for Firmware Update in Controller Management is inappropriate
SCGCQ00569098 - Enter security key for locked drives screen, press down to get to OK, OK will show up again on right
SCGCQ00598822 - VD details display is improper in Expand Virtual Drive
SCGCQ00613822 - Advanced Controller Properties- Power Saving Settings has broken form
SCGCQ00556839 - Able to select EKM even when the EKM FOD key is removed from the system.
SCGCQ00589301 - System/HII hang when clicks on Hardware Components menu option in HII.
SCGCQ00595864 - On Success of creating Drive Security Form loads into Advanced controller properties
SCGCQ00598431 - IMR Liberator Drop Down option in VD properties for Cached is present
SCGCQ00610889 - Customize help string for Select Interface Type
SCGCQ00615190 - Fill Controller Index in RouteConfig + for UF003 calculate checksum only for the actual config size
SCGCQ00593558 - Auto Learn Mode is showing wrong data
SCGCQ00612574 - Addressed review comments
SCGCQ00613820 - Typo in HII form Controller Status
SCGCQ00622464 - Toggling between Legacy to Uefi mode vice versa junk values seen .
SCGCQ00524969 - HII PKG 0006/Going from LKM to EKM asks for a Current Security key Identifier and Security key.
SCGCQ00590465 - On selecting a wrong parameter for size while creating VDs, Options greyed, Create VD page exits to parent page.
SCGCQ00595463 - Security feature is enabled but HII sees "Drive Security" as disabled
SCGCQ00571359 - UCM Phase 1: Typo "Clear Configuration" -> "Clear Configuration"
SCGCQ00573222 - Handling Code Collaborator Review Defects for SCGCQ00568814 and SCGCQ00569197
SCGCQ00575062 - added a while loop and take care of the multiple PD Groups scenario.
SCGCQ00578190 - HII should calculate checksum before setting bios data (MR_BIOS_DATA)
SCGCQ00597641 - MR6.3 HII aesthetic change
SCGCQ00503036 - Changing Percentage of Space to Expand Does not Update Final VD Size
SCGCQ00574041 - AIM (Agentless Inventory Manager) Issues
SCGCQ00574989 - Creation+ FW updation+ Scan foreign Configuration is disabled/grayed out in HII page
SCGCQ00614466 - HII 03.07.05.00/Under advanced controller properties and selecting Cache and Memory, it says's "scontroller cache"
SCGCQ00614675 - To address FW Update help Strings
SCGCQ00619028 - Not able to schedule CC in concurrent mode from HII(03.07.09.00).
SCGCQ00526978 - HII. Provide controller FW update function
SCGCQ00568814 - HEFU. Simplify controller property page
SCGCQ00568706 - Remove limitation for creating R6 in HII for OEM
SCGCQ00612466 - Provide pop-up to display current version and update fw version as part of HEFU HII Firmware Update functionality
SCGCQ00571579 - (Implemented) - Create a formset with classGUID that customer has provided.
SCGCQ00569197 - Move Disable Protection option from Controller Management to VD management
SCGCQ00557522 - System hang observed when the "PdInfo.userDataBlockSize" is set to 0
SCGCQ00601110 - Able to select EKM even when the EKM FOD key is removed from the system.
SCGCQ00601103 - Enter security key for locked drives screen, press down to get to OK, OK will show up again on right
SCGCQ00601107 - HII PKG 0006/Going from LKM to EKM asks for a Current Security key Identifier and Security key.
SCGCQ00601119 - HII help for Boot error handling does not display "Stop On Error" option
SCGCQ00644857 - Remove FMP installed on the controller handle in HII
SCGCQ00644858 - RSOD during POST after enabling SecureBoot - HEFU.ROM should report exact size of .EFI image
SCGCQ00629813 - RSOD during POST after enabling SecureBoot - HEFU.ROM should report exact size of .EFI image
SCGCQ00601113 - HII\EKM-LKM without reboot should show proper message
SCGCQ00601117 - UCM Phase 1: Allow user to select RAID level when controller has other VD + error handling
SCGCQ00572986 - System hang observed when the "PdInfo.userDataBlockSize" is set to 0
SCGCQ00644575 - Consistency Check Start - remove mm/dd/yyyy from the string as the format is out of control of LSI
SCGCQ00596920 - Missing BBU caused disappearance of Enclosure Mgmt opt in BIOS setup
SCGCQ00603235 - HII help window shows unsupported stripe sizes
SCGCQ00601116 - added a while loop and take care of the multiple PD Groups scenario.
SCGCQ00601118 - UCM Phase 1: Typo "Clear Configuration" -> "Clear Configuration"
SCGCQ00601120 - In HII on a ready drive we are able to see Used space as 40Gb.
SCGCQ00644786 - Enhance help message for PD/VD Operation field

FCODE - 4.16.08.00

SCGCQ00553069 - PCLI(1.07.05) Sparc: Command "cli set securitykey=Lsi@12345" fails with errcd "1001" and errmsg "invalid key".
IMR NVDATA - 3.1403.01-0061
SCGCQ00709554 - Revise Drive Spin-Up Timing on OEM 12G iMR and MR Boards
SCGCQ00685089 - Addition of ManPage1 values to the xml file.
SCGCQ00696438 - Customer NVDATA Change request for iMR
SCGCQ00692947 - Dual write NVDATA changes for customer
SCGCQ00673357 - Flatwoods Showing Same Slot Number for All Drives
SCGCQ00658482 - breakMirrorRAIDSupport for single span Raid 1

BootBlock - 3.02.00.00-0001

SCGCQ00685115 - Memory/battery problems in Focused Regression
SCGCQ00505902 - Coherency bit is disabled in SRAM TLBs

Ctrl-R - 5.04-0002

SCGCQ00644489 - Added a new Control to enable/disable JBOD on the controller in Ctrl Mgmt page.
SCGCQ00648965 - Display the Battery status as N/A for iMR cards.
SCGCQ00584991 - current write policy is not getting updated until we press f5
SCGCQ00584993 - unable to display the reason for difference in write policy
SCGCQ00593822 - Both the Connector information(0-3 & 4-7) is not shown in PD properties while connected in Multipath
SCGCQ00579583 - Write policy is not added with writeback with BBu when MFC is set
SCGCQ00573077 - VD Erase will be disabled in Ctrl+R when Initialization on particular VD is aborted
SCGCQ00585013 - Added the code to unset the boot-device to NONE
SCGCQ00584991 - current write policy is not getting updated until we press f5 .
SCGCQ00584993 - unable to display the reason for difference in write policy
SCGCQ00593822 - Both the Connector information(0-3 & 4-7) is not shown in PD properties while connected in Multipath
SCGCQ00579600 - Write policy is not added with writeback with BBu when MFC is set
SCGCQ00579607 - VD Erase will be disabled in Ctrl+R when Initialization on particular VD is aborted
SCGCQ00585013 - Added the code to unset the boot-device to NONE

PCLI - 1.07.05

SCGCQ00501437 - StorCLI - MR 6.2 StorCLI help syntax is wrong for R1EC
SCGCQ00518543 - PCLI Sparc(1.07.02):" Cli show all" command fails with error msg "Error! App exec failed in FW PCLIError! Internal".

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Intel Drivers