Intel MR 3108 ROC Hardware RAID Firmware 24.10.0-0017 Download

Posted at December 21, 2024 by PCI-DB Team

Intel MR 3108 ROC Hardware RAID Firmware 24.10.0-0017 Description

Versions:

- Firmware 4.290.00-4536
- BIOS 6.28.04.0
- NVDATA 3.1507.00-0006
- UEFI_Driver 0x06110200(signed)
- Hii 03.17.14.00(signed)
- Ctrl-R 5.13-1100
- ROMENV 1.09
- BootBlock 3.07.00.00-0002
- FCODE 4.17.08.00
- PCLI 1.07.05

Changes:

SCGCQ00718801 - (Closed) - FW breaks to MonTask: line 1168 in file ../../raid/raid.c during RAID Operations
SCGCQ00724451 - (Closed) - FW breaks to MonTask: line 889 in file ../../raid/bladeDMA.c while creating a filesystem on R5 VD.
SCGCQ00725844 - (Closed) - Intruder pre alpha 2 : On a R1 to R5 reconstructing Virtual Drive, IO failed with data miscompare
SCGCQ00729599 - (Closed) - Intruder pre alpha 2 : "MonTask: line 396 in file ../../ssd/ssd_cache_fw.c" with IO on R5 VD with a CacheCade VD in WB
SCGCQ00747258 - (Closed) - .10 PL cause DataTLB error with MR FW.
SCGCQ00751361 - (Closed) - 512e support needs to be enabled in MR FW
SCGCQ00788071 - (Closed) - Code review items were fixed
SCGCQ00788072 - (Closed) - Code Review fixes for review Review 38871 -Integrate 6.5 Changes with Intruder Code stream
SCGCQ00791766 - (Closed) - Rebase Dev stream with Integration 6.5 manual changes
SCGCQ00794871 - (Closed) - FW breaks to MonTask: line 257 in file ../../dm/src/dmDrvPrep.c when booting FPGA
SCGCQ00807498 - (Closed) - Data corruption detected with offload and restore operation
SCGCQ00812867 - (Closed) - Data corruption reported with Intruder ONFI2 offload and restore operation
SCGCQ00819772 - (Closed) - Flash wrongly discovered as transported across back to back offload and restore cycles
SCGCQ00822311 - (Closed) - ONFI unable to offload to controllers with multiple chipselects
SCGCQ00823817 - (Closed) - FPGA stream missing .4 release stream content
SCGCQ00831595 - (Closed) - FW hanging with 0.6 release while bootup.
SCGCQ00832908 - (Closed) - MSM displays error message if 'Schedule Consistency Check' is selected.
SCGCQ00843098 - (Closed) - Un-correctable ECC error on Armstong board during cold boot
SCGCQ00844777 - (Closed) - Modifying SBR PnP IDs offset
SCGCQ00845435 - (Closed) - Data Corruption on WB VDs
SCGCQ00846621 - (Closed) - Medium error correction events were not reported
SCGCQ00848339 - (Closed) - FW hangs during cache flush after restore cache from flash.
SCGCQ00850401 - (Closed) - ONFI: FC0 CS0 offload meta length not valid:0, expected:7c00 causing restore to not start after offload.
SCGCQ00850839 - (Closed) - FW hangs after re-inserting SATA drive in direct connect topology during I/O.
SCGCQ00856977 - (Closed) - Unable to update drive firmware on customer specific FDE SATA SSDs
SCGCQ00858697 - (Closed) - For Sugon Romb dont Initialize the port activity LED's GPIO.
SCGCQ00863880 - (Closed) - MR_6.9_FW : Core 0 exception seen while trying to import foreign configuration with pinned cache present.
SCGCQ00864054 - (Closed) - Perform the PCI release retry while performing BISR on the second CPU.
SCGCQ00865116 - (Closed) - ROC Temp GPIO action item
SCGCQ00866261 - (Closed) - Invader firmware (4.280.00-4331 in MR 6.7) with write-verify has abnormal behavior/performance.
SCGCQ00867065 - (Closed) - Increase CACHE HEADER version, since new member was added to PinnedCacheDataStructure(Persistent DRAM)
SCGCQ00872875 - (Closed) - MR_6.9: MonTask: line 1280 in file ../../raid/1078dma.c. DCDB cmd timed out
SCGCQ00872889 - (Closed) - MR6.9_FW : Kill adapter seen while issuing Task Management in loop on 240 JBODs with IOs.
SCGCQ00873991 - (Closed) - Data TLB error occured after issuing task abort from host
SCGCQ00878414 - (Closed) - 6.9 : Write perf drops in 16R5 WT NoRA DCD SS64 1MB IO at QD128/256
SCGCQ00878432 - (Closed) - Blade DMA errors observed while running IOs
SCGCQ00878587 - (Closed) - MonTask: line 245 in file ../../raid/1078int.c while running I/Os with 64VDs and pull out drives belonging to CacheCade VD
SCGCQ00879193 - (Closed) - Restricting the VD deletion optimization to reduce IO freeze to least latency mode.
SCGCQ00881001 - (Closed) - StorCLI Reports Incorrect TFM Manufacturing Date
SCGCQ00881901 - (Closed) - FW hang, even-after Task Abort is successful on a drive in Linux OS
SCGCQ00882125 - (Closed) - On receiving CACHE_FLUSH_DCMD, set forceCacheflush flag to 1 to flush the cache
SCGCQ00882897 - (Closed) - Need to set perfTunerMode appropriately on controller reset.
SCGCQ00884589 - (Closed) - Windows BSOD when upgrade FW 24.6.0-0040 to 24.8.0-0026 with driver 6.707.08.00
SCGCQ00890133 - (Closed) - Invader 6.9: FW breaks MonTask: line 245 in file ../../raid/1078int.c with IOs on max VD configured and BGOps
SCGCQ00891924 - (Closed) - Buffer Size is set to 1M and number of BSB per BB is set to 1.
SCGCQ00893588 - (Closed) - MR6.9_FW : IO halts on JBODs with read/write error when the target drives are reset via MFI or MPT path on Linux distro
SCGCQ00895554 - (Closed) - MR_6.9_FW: Kill adapter during test run
SCGCQ00904905 - (Resolved) - Copyback fails to start and causes a FW fault
SCGCQ00717238 - (Closed) - MR Intruder Fault x6101 - FW breaks to Montask: line 1557 in file ../../dm/pl2/pliopi.c
SCGCQ00738085 - (Closed) - Change flags for each sge in the sglist.
SCGCQ00750804 - (Closed) - FW breaks to MonTask: line 299 in file ../../raid/1078int.c when try to run IO on 32 drive R0 16 VD configuration.
SCGCQ00771238 - (Closed) - remove Cache split related changes from Int stream
SCGCQ00788087 - (Closed) - Multi- SAS Core - Code reivew defect fixes.
SCGCQ00788526 - (Closed) - Defect to check in code changes reported by static analysis tool for intruder
SCGCQ00803219 - (Closed) - Data corruption when destaging pinned cache after foreign config import.
SCGCQ00812295 - (Closed) - Back to back restore happen because flash region not toggled after a restore operation
SCGCQ00819786 - (Closed) - FW should prepare and arm HW for second offload before starting cache flush
SCGCQ00836031 - (Closed) - NVDATA and Controller Properties all zero
SCGCQ00845921 - (Closed) - Development defect for Cache Offload work around.
SCGCQ00846655 - (Closed) - Battery relearn timed out on Supercap on Armstrong board
SCGCQ00847001 - (Closed) - MR6.6 Controller is not accessible through OOB before OS is up and running
SCGCQ00848264 - (Closed) - Development defect for flash chip M83C workaround in Intruder
SCGCQ00850368 - (Closed) - Firmware Faults with error code 0x22 after an OCR
SCGCQ00855837 - (Closed) - A race condition exists while creating the flash filesystem and making the corresponding entries in NVRAM
SCGCQ00855845 - (Closed) - Disable pause for memory offload control 1.
SCGCQ00857181 - (Closed) - On performing back to back target reset on the same JBOD results into online controller reset(OCR)
SCGCQ00857680 - (Closed) - MR 6.7 Point : Few test cases fail when PCIeCV tool is executed
SCGCQ00857692 - (Closed) - MR 6.9 : Firmware allows to perform Reconstruction when Pinned Cache is present.
SCGCQ00859850 - (Closed) - Pinned Cache lost after trigger few OCR and reboot server as result data got corrupt
SCGCQ00860066 - (Closed) - Firmware breaks to montask while importing the Foreign Config.
SCGCQ00860503 - (Closed) - MR 6.9 : Controller boots to OS Even when Pinned Cache is present and Boot Error handling is set to Stop on Error.
SCGCQ00860635 - (Closed) - Firmware hang is observed when Cache Offload is interrupted by power restore.
SCGCQ00860716 - (Closed) - Firmware allows to create more than 64 logical drives in legacy mode.
SCGCQ00861819 - (Closed) - Address code review defects for ER SCGCQ008554
SCGCQ00871973 - (Closed) - FW allows CCVD deletion with pinned windows
SCGCQ00873239 - (Closed) - FW downgrade fails with IOs and BGops .
SCGCQ00874200 - (Closed) - Re-eanbling 1MB IO support.
SCGCQ00878554 - (Closed) - Core 0 exception in line 245 in ../../raid/1078int.c while Target reset on PDs and BG Operations in parallel
SCGCQ00879198 - (Closed) - MR6.9_FW : Assertion failure in ../../dm/src/dmDrvPrep.c at line 836: while Cable pull push on secondary enclosure.
SCGCQ00882742 - (Closed) - Fix coverity defects
SCGCQ00886685 - (Closed) - Add sanity check for iPtr and rPtr after restore is completed.
SCGCQ00894472 - (Closed) - Adjust cache thresholds appropriately after the pinned cache is generated and volumes are retained in WB mode.
SCGCQ00894608 - (Closed) - OS become unresponsive after creating multiple sliced VD's
SCGCQ00899762 - (Closed) - SKINNY compilation was broken after fixing SCGCQ00882125
SCGCQ00906129 - (Closed) - Intruder : Data Corruption issue seen while running cable breaker with CCVD associated
SCGCQ00908325 - (Closed) - Undoing the changes of CSET activity SCGCQ00803718
SCGCQ00914740 - (Closed) - 6.9: Default values does not get picked up for un-changed controller property sharing same byte.
SCGCQ00764924 - (Closed) - FW breaks to Montask: line 891 in file ../../raid/bladeDMA.c while creating file system on VDs.
SCGCQ00788106 - (Closed) - Code review fixes for 33080
SCGCQ00819441 - (Closed) - Port ONFI changes to Intruder .5 stream.
SCGCQ00823465 - (Closed) - Reconstruction from R1 to R5 causing FW hang.
SCGCQ00844839 - (Closed) - Armstrong board causing HP server to hang during bootup.
SCGCQ00845436 - (Closed) - Limit the Memory size to 1GB as temp workaround to DC issue.
SCGCQ00850220 - (Closed) - Check in OCR work around
SCGCQ00850441 - (Closed) - iMR 6.1.1 : Exception seen during OS Reboot heat run test
SCGCQ00850818 - (Closed) - Controller hangs during post if you have dirty cache that needs to be flushed to the VD.
SCGCQ00851267 - (Closed) - Firmware halted after trigger OCR with I/O
SCGCQ00852327 - (Closed) - When no drives connected tlb error is seen
SCGCQ00853020 - (Closed) - Firmware Test API returns incorrectly that hardware is armed for offload, when supercap is bad.
SCGCQ00855322 - (Closed) - !!! Firmware initialization failed. Fault code = 0x4 !!!
SCGCQ00857528 - (Closed) - MR_6.8:FW hits to MonTask: line 4946 in file ../../raid/ld.c while multipath push pull with patrol read
SCGCQ00859961 - (Closed) - Cannot disable patrol read on an Armstrong controller.
SCGCQ00865963 - (Closed) - Too many event in firmware log : onfiHwIsOffloadSustainableStateSet onfi_status 0
SCGCQ00872140 - (Closed) - MR6.9:'Watchdog Timer Exception' followed by FW crash after initiating PD Erase on UG PD, with BG operation & IO's on 64 VD's
SCGCQ00873201 - (Closed) - Avoid cache FLUSH during VD Deletion to reduce IO Freeze time on other VDs
SCGCQ00874332 - (Closed) - MR6.9_FW : FW hits montask due to a non-spinning up FDE drive, issue seen on repeated reboots.
SCGCQ00880919 - (Closed) - MR6.9_FW : Controller discovery failed due to pending Boot messages, adapter at baseport not responding.
SCGCQ00886351 - (Closed) - MR 6.8 : Few test cases fail when PCIeCV tool is executed
SCGCQ00900250 - (Closed) - Send appropritate MFI status for the command which needs to be aborted
SCGCQ00827430 - (Closed) - Loss of smart recovery blocks in a small window when switching regions
SCGCQ00832205 - (Closed) - Development defect to fix Code Coverity issues found in Intruder 0.6 Stream.
SCGCQ00845707 - (Closed) - MSM reports 4MB and 8MB FW image is corrupt and does not allow flashing Armstrong board.
SCGCQ00846582 - (Closed) - SATA drives not detected in direct connect topology -MR
SCGCQ00846657 - (Closed) - ONFI offload descriptors are not set to offload all valid DATA cache
SCGCQ00859720 - (Closed) - On OCR or reboot, retain volumes in WB if the number of pinned buffers is less than 50% of available buffers.
SCGCQ00859975 - (Closed) - Code review defect with 6.9 merge with Inv team
SCGCQ00860140 - (Closed) - Coverity: fix Coverity defect 16729
SCGCQ00874357 - (Closed) - Data TLB error occured while tring dereference invalid command ID
SCGCQ00877673 - (Closed) - Kill adapter while running IO with Task Reset on JBODs
SCGCQ00878923 - (Closed) - Remove PinnedCacheDataStructure totalPinnedBbs and totalPinnedBsbs update in PinCacheForLd()
SCGCQ00881919 - (Closed) - Data TLB error found while running the target reset script with multipath cable pull-push operation
SCGCQ00848368 - (Closed) - Armstrong Controller hangs when make JBOD from powersave PD.
SCGCQ00848372 - (Closed) - API calls to corrupt and verify DIS on ONFI NAND flash are not available in Intruder code release
SCGCQ00856566 - (Closed) - Code review defect with 6.9 merge with Inv team
SCGCQ00866487 - (Closed) - MR6.9_FW : sasPortNumberValid bit does not get updated in CtrlR
SCGCQ00867120 - (Closed) - MR6.8_FW : DISM stuck at device discovery on enclosure power cycle, Devices present with DM but not reflected in upper layers
SCGCQ00869626 - (Closed) - Compilation Error in Invader with Intruder merged code
SCGCQ00878097 - (Closed) - MR6.9:Assertion failure in ../../raid/cache.c at line 774, after pulling out the enclosure cable
SCGCQ00864019 - (Closed) - One deletion of CCVD FW displays incorrect CCVD target id and remaining CacheCade size on the system
SCGCQ00878150 - (Closed) - Controller killed on issuing OCR from StorCLI after disabling it from OS.
SCGCQ00881005 - (Closed) - Code cleanup issues.
SCGCQ00848321 - (Closed) - Offload starting with residual power, which corrupts metadata
SCGCQ00849733 - (Closed) - Development defect to remove the hardcoded TFM VPD values in firmware for Intruder.
SCGCQ00863348 - (Closed) - Remove checkSysPwrStatus() and processSysPwrReturn() functions.
SCGCQ00866206 - (Closed) - Modify app.ld to address iopath and dramCode region overflow - MR 6.9Intruder
SCGCQ00869060 - (Closed) - Intruder6.9 code review changes
SCGCQ00877100 - (Closed) - TTY log dump is not persistent for multiple boots.
SCGCQ00848328 - (Closed) - L2 Cache Error was NOT detected at POST after inject ECC error
SCGCQ00859968 - (Resolved) - Deleting duplicate/unwanted files from source contr
SCGCQ00679021 - (Closed) - Bringup MR Intruder fpga with Init bit stream.
SCGCQ00681940 - (Closed) - Following FW interfaces are implemented
SCGCQ00696857 - (Closed) - Invader 6.3 GCA code ported to Invader stream
SCGCQ00713577 - (Closed) - 2.1b Bitstream related MR Fw changes for Dallas FPGA Validation.
SCGCQ00760455 - (Closed) - Integrate .12 PL into MR code
SCGCQ00772420 - (Closed) - Merge 6.5 Changes with Intruder Code stream
SCGCQ00791733 - (Closed) - New PL integrated.
SCGCQ00804452 - (Closed) - Integrate Latest PL .19 with MR stack
SCGCQ00813852 - (Closed) - PL 0.85 release check-in
SCGCQ00813853 - (Closed) - Flash header changes for Intruder
SCGCQ00814430 - (Closed) - Code bring up on 3108 controller
SCGCQ00817806 - (Closed) - Updating release script for Intruder code base
SCGCQ00827051 - (Closed) - Integrate .22 PL and Invader 6.7 code.
SCGCQ00827085 - (Closed) - Adding Support in Firmware for a new Flash Controller for Intruder.
SCGCQ00834328 - (Closed) - Enable Synchronous mode of communication between Intruder and Flash Chip.
SCGCQ00840256 - (Closed) - Code changes for A0 silicon & Eval board.
SCGCQ00842347 - (Closed) - Creation and productization of new product SKU for 9361-8i board with 2GB of memory
SCGCQ00844787 - (Closed) - support for dual rank ddr memory in Intruder, new pl library, and DMA workaround
SCGCQ00846939 - (Closed) - Re-branding effort for customer.
SCGCQ00850707 - (Closed) - Fault LED support for predictive failure drives for SGPIO
SCGCQ00855889 - (Closed) - OEM wants controller VPD reporting should be disable
SCGCQ00856088 - (Closed) - GPIO Settings for a customer
SCGCQ00861994 - (Closed) - Check-in 6.9 Intruder code changes to use same MEM_FIXED for Inruder and Invader
SCGCQ00864357 - (Closed) - Check-in PL 250.34 to Inruder A0.
SCGCQ00865372 - (Implemented) - Reduce Command Block Latency during Background Operations
SCGCQ00882016 - (Closed) - Integrating PL 06.00.05.00 with 6.6 FW stream.
SCGCQ00884951 - (Closed) - Integrate 08.00.05.00 MR PL with MR 6.8
SCGCQ00893029 - (Closed) - Add support to enable/Disable of Large IO Support - 1 MB IO
SCGCQ00908329 - (Closed) - SCSI Inquiry string should not change in current generation HBA
SCGCQ00681943 - (Closed) - ONFI debug functionality implemented to test software based offload and restore operations
SCGCQ00687251 - (Closed) - Implement Cache-split feature
SCGCQ00710266 - (Closed) - Intruder Dual SAS core changes.
SCGCQ00721312 - (Closed) - Add support for TM and Error handling with dual sas core to MR.
SCGCQ00772441 - (Closed) - Intergrate PL 0.13 to Intruder fpga
SCGCQ00772443 - (Closed) - Put Infrastructure to compile Intruder and Invader on same code base.
SCGCQ00792619 - (Closed) - Implemented as part of Intruder FPGA bringup.
SCGCQ00837210 - (Closed) - For the new flash chip in Intruder, additional DDR Regions is memset to 0 after cache restore is complete.
SCGCQ00841116 - (Closed) - Add Manual BISR to bring up secondary core for Intruder
SCGCQ00862035 - (Closed) - New LED to indicate Over Temperature in Intruder.
SCGCQ00809693 - (Closed) - Invader 6.6 Code stream merge to Intuder.
SCGCQ00852052 - (Closed) - Add pl 0.250.27 to Intruder code.
SCGCQ00853299 - (Closed) - Incorporate Memory Port difference for xor base address for Intruder
SCGCQ00853423 - (Closed) - Implement the HW workaround in Intruder to recover from warm reset
SCGCQ00855457 - (Implemented) - Task management support for JBOD/sysPD to Windows and Linux drivers (follow-on to PR SCGCQ00687438)
SCGCQ00860586 - (Closed) - Add 5/15 6.9 action item changes
SCGCQ00861695 - (Closed) - Add support for Micron M83C flash part for Intruder generation products.
SCGCQ00880731 - (Closed) - Integrate Phase 9 PL 9.0.0.0 with MR 6.9
SCGCQ00781019 - (Closed) - Retain Configuration btw boots on FPGA environment
SCGCQ00846602 - (Closed) - New GPIO definitions for Intruder
SCGCQ00868957 - (Closed) - Integrate Phase 9 PL (version 9.0.0.0) with MR 6.9
SCGCQ00841181 - (Closed) - A0 Intruder bring activities Part 2
SCGCQ00856859 - (Closed) - Check in new pl 250.32
SCGCQ00860624 - (Closed) - Update ManPage12 and ManPage13 as per new structures defined for Intruder
SCGCQ00852061 - (Closed) - MPIC configuration table changes
SCGCQ00852502 - (Implemented) - Avoid Moving WB volumes to WT on pinned cache genera
SCGCQ00805369 - (Port_Complete) - Bad physical drive caused controller error recovery go in loop
SCGCQ00833943 - (Port_Complete) - MR6.7-Beta:FW hits to MonTask: line 1272 in file ../../raid/1078dma.c after Injecting media error in loop on CCVD metadata
SCGCQ00833944 - (Port_Complete) - MR6.7-Beta:FW hits to MonTask: line 1272 in file ../../raid/1078dma.c after Injecting media error in loop on CCVD metadata
SCGCQ00833945 - (Port_Complete) - MR6.7-Beta:FW hits to MonTask: line 1272 in file ../../raid/1078dma.c after Injecting media error in loop on CCVD metadata
SCGCQ00833946 - (Port_Complete) - MR6.7-Beta:FW hits to MonTask: line 1272 in file ../../raid/1078dma.c after Injecting media error in loop on CCVD metadata
SCGCQ00837206 - (Port_Complete) - Setting the Learn Cycle property of iBBU09 gives an I2C error
SCGCQ00838545 - (Port_Complete) - MR_6.8_FW: Fw hits to MonTask: line 1272 in file ../../raid/1078dma.c while running IO in VM
SCGCQ00841545 - (Port_Complete) - Performing a cable pull/push with array property change resulting into FW hang.
SCGCQ00844445 - (Port_Complete) - Commands to the fde drives are not responding within 500ms.
SCGCQ00845203 - (Port_Complete) - MR_6.8_FW:Firmware halted and restarted while doing flash erase on the onfi flash
SCGCQ00848415 - (Port_Not_Required) - flush cache with write_verify on R0 volume and sata drive
SCGCQ00849553 - (Port_Complete) - Unexpected controller reset during test run
SCGCQ00849614 - (Port_Complete) - chain element for non RW commands were not pulled in the FW
SCGCQ00849620 - (Port_Complete) - Deleting a Cachecade VD (CC VD) results in a firmware hang situation.
SCGCQ00850990 - (Port_Complete) - Rebuild Performance for RAID 1 arrays is slower.
SCGCQ00851993 - (Port_Complete) - Patrol Read Properties window does not pop up on MSM
SCGCQ00853534 - (Port_Complete) - L2 unrecoverable cache error was seen during Patrol read properties modification in certain conditions.
SCGCQ00854160 - (Port_Complete) - Controller Reboots after doing an OCR with IOs running in the background
SCGCQ00854164 - (Port_Complete) - Controller cache fails to destage when multiple SVDs are present
SCGCQ00854165 - (Port_Complete) - Controller cache fails to destage when multiple SVDs are present
SCGCQ00854168 - (Port_Complete) - Controller cache fails to destage when multiple SVDs are present
SCGCQ00854169 - (Port_Complete) - Controller cache fails to destage when multiple SVDs are present
SCGCQ00854170 - (Port_Complete) - Controller cache fails to destage when multiple SVDs are present
SCGCQ00869785 - (Port_Complete) - Fault LED support for predictive failure drives for SGPIO
SCGCQ00873092 - (Port_Complete) - FW allows CCVD deletion with pinned windows
SCGCQ00873093 - (Port_Complete) - FW allows CCVD deletion with pinned windows
SCGCQ00873094 - (Port_Complete) - FW allows CCVD deletion with pinned windows
SCGCQ00878362 - (Port_Complete) - Code collab fixes delivered
SCGCQ00878401 - (Port_Complete) - Cleanup device wait queue if drive is no longer online
SCGCQ00882474 - (Port_Complete) - Disable FLR support in MR FW to address VMware guest VM abrupt shutdown issue
SCGCQ00886272 - (Port_Complete) - Windows BSOD when upgrade FW 24.6.0-0040 to 24.8.0-0026 with driver 6.707.08.00
SCGCQ00886665 - (Port_Complete) - disableImmediateIO is not reflected in FW
SCGCQ00886666 - (Port_Complete) - disableImmediateIO is not reflected in FW
SCGCQ00886826 - (Port_Complete) - Need to set perfTunerMode appropriately on controller reset.
SCGCQ00889407 - (Port_Complete) - MonTask: line 245 in file ../../raid/1078int.c while running I/Os with 64VDs and pull out drives belonging to CacheCade VD
SCGCQ00889884 - (Port_Complete) - MonTask: line 245 in file ../../raid/1078int.c while running I/Os with 64VDs and pull out drives belonging to CacheCade VD
SCGCQ00891282 - (Port_Complete) - Recon VD made "degraded" when the recon pd is pulled out allowing for rebuild once the drive is plugged back in.
SCGCQ00891288 - (Port_Complete) - Cisco - Colusa1 MonTask after Initiating a Raid Level migration
SCGCQ00908121 - (Port_Complete) - on creating 240VD and rebooting the server, FW breaks into montask.
SCGCQ00908153 - (Port_Complete) - LUID gets changed during foreing import from non-240VD FW to 240VD FW
SCGCQ00914823 - (Port_Complete) - Created VD configuration with PDs released from previous VD erased will lost after next reboot
SCGCQ00803718 - (Port_Complete) - Ctrl-r and HII does not show proper message when you try to import the 65th VD.
SCGCQ00838560 - (Port_Complete) - MR6.8_FW : Unable to Convert a JBOD PD to UG in Solaris
SCGCQ00843936 - (Port_Complete) - Handling Functional Level Reset (FLR) .
SCGCQ00844446 - (Port_Complete) - Enable I2C clock frequency of 100kHz for specific OEM is not working accurately
SCGCQ00844447 - (Port_Complete) - Handle enabling disk "write" cache setting from OS for OEM
SCGCQ00846479 - (Port_Complete) - Secure Erase on SATA SSD via CtrR or HII leads to unresponsive application, Secure erase failing intermittently
SCGCQ00849580 - (Port_Complete) - Failed to import iMR RAID configuration to 12G MR
SCGCQ00850924 - (Port_Complete) - MR & iMR FW Work-around is required for 3x08 chip Errata ID - 2012-RC714 for PCIE 3.0 compliance
SCGCQ00853537 - (Port_Not_Required) - L2 unrecoverable cache error was seen during Patrol read properties modification in certain conditions.
SCGCQ00854177 - (Port_Complete) - Vd erase does not resume after reboot in the presence of CCVD
SCGCQ00871400 - (Port_Complete) - Fault LED support for predictive failure drives for SGPIO
SCGCQ00886271 - (Port_Complete) - Windows BSOD when upgrade FW 24.6.0-0040 to 24.8.0-0026 with driver 6.707.0
SCGCQ00887602 - (Port_Complete) - MR 6.8 : Few test cases fail when Intel PCIeCV tool is executed
SCGCQ00895459 - (Port_Complete) - Removal of "LdDcmd return pinned list 0" spam in FW logs.
SCGCQ00844068 - (Port_Complete) - iMR:6.5-Exception in core 0 is seen when drives are spun down and an ocr is triggered
SCGCQ00844152 - (Port_Complete) - FW doesn't poll all temp sensor channels every 5 seconds
SCGCQ00853147 - (Port_Complete) - Continuous "TASK_ABORT_INTERNAL" prints observed in FW, after running heavy IO's on JBOD configured using 12Gig SAS SSD
SCGCQ00868527 - (Port_Complete) - MR 6.9 : Controller boots to OS Even when Pinned Cache is present and Boot Error handling is set to Stop on Error.
SCGCQ00870846 - (Port_Complete) - FW unable to detect the inserted drives
SCGCQ00876154 - (Port_Complete) - SAS and SATA HDD R0 and R10 1M performance regressions (-15% to -35%) at QD16 to QD256
SCGCQ00882149 - (Port_Complete) - StorCLI reports success on 4MB MR FW package flashing on iMR only controller.
SCGCQ00884719 - (Port_Complete) - 'Fw initializing devices' hangs on controller with specific failed drives on backplane
SCGCQ00891273 - (Port_Complete) - Megaraid Thunderbolt controller reports cache memory size as 0 when no logical drives are present.
SCGCQ00841533 - (Port_Complete) - Instruction TLB error seen when auto configuration command exectued from CLI application
SCGCQ00843390 - (Port_Complete) - Megaraid-sas driver hang with Falcon card
SCGCQ00851886 - (Port_Complete) - MSM displays error message if 'Schedule Consistency Check' is selected.
SCGCQ00892136 - (Port_Complete) - MR 6.6.3 "storcli /c0 show all" shows lot of bad block messages in the log
SCGCQ00835227 - (Port_Complete) - STASH firmware entered fault state with SSD drive
SCGCQ00872263 - (Port_Complete) - Fw crash and BIOS RSODs when VD1 deleted with recon on a PI VD(VD2) and Slow init on VD3.
SCGCQ00841772 - (Port_Complete) - MR firmware reports no smart error when attaching a PFA drive
SCGCQ00876142 - (Port_Complete) - FW unable to detect the inserted dr
SCGCQ00879731 - (Closed) - Legacy OpROM: Handle the conditions for battery failed state as per the Battery design do
SCGCQ00882729 - (Closed) - Legacy OpROM: Controller POST shows JBOD found on host adapter, when number of INT13 device is > deviceExposure
SCGCQ00866982 - (Closed) - Legacy OpROM: Overlapping seen in POST in presence of two controllers and foreign config during CTRL-H laun
SCGCQ00834718 - (Closed) - PNPs and support for 16 port 12G designs
SCGCQ00898506 - (Closed) - OS doesn't boot after installing OS on the 100th VD , while having 240 VDs created in EFI mod
SCGCQ00834720 - (Closed) - PNPs and support for 16 port 12G designs
SCGCQ00844774 - (Closed) - Handle coverity defects
SCGCQ00880737 - (Closed) - Handled the coverity defects.
SCGCQ00892931 - (Closed) - Not able to set Controller properties
SCGCQ00896827 - (Closed) - Cannot convert the state of drive from JBOD to UG if the drive is not 16byte CDB
SCGCQ00825741 - (Closed) - UEFI Driver: Compilation error when debug Flags are enabled
SCGCQ00852480 - (Closed) - "Question value mismatch type!Press Enter" message is displayed while entering create virtual drive page
SCGCQ00878350 - (Closed) - HII Enclosure Management form multiple time navigation results in hang/multiple entries of enclosure seen
SCGCQ00879673 - (Closed) - HII: Add GUID check for bootable drive
SCGCQ00894460 - (Closed) - Controller status inconsistency between Dashboard and Controller management in HII
SCGCQ00915093 - (Closed) - HII: Updating LargeIOSupport as per the new API changes
SCGCQ00870398 - (Closed) - Incomplete Port enumeration i.e connector information is displayed for ESM and PD's in HII
SCGCQ00873973 - (Closed) - Profile Based DHS creation grayed out
SCGCQ00879726 - (Closed) - HII: Handle the conditions for battery failed state as per the Battery design doc
SCGCQ00889780 - (Closed) - HII: Address review comments
SCGCQ00903490 - (Closed) - HII RLM for only R0 available when 18 or more drives are present
SCGCQ00860564 - (Closed) - In Make UG warning message OS JBOD drives are not listed
SCGCQ00898506 - (Closed) - OS doesn't boot after installing OS on the 100th VD , while having 240 VDs created in EFI mode
SCGCQ00881426 - (Closed) - VD properties does not display Emulation type.
SCGCQ00893928 - (Closed) - HII: Address review comment
SCGCQ00834719 - (Implemented) - PNPs and support for 16 port 12G designs
SCGCQ00834720 - (Closed) - PNPs and support for 16 port 12G designs
SCGCQ00844917 - (Implemented) - OEM requesting to do a WRITE VERIFY prior to flushing cache. This needs to be managed via CLI
SCGCQ00893152 - (Closed) - HII: Add support to enable/Disable of Large IO Support
SCGCQ00828031 - (Implemented) - Add support to detect that an OS is installed on a JBOD
SCGCQ00854621 - (Closed) - Provide a more descriptive port enumerati
SCGCQ00888846 - (Port_Complete) - HII: Spelling mistakes in strings
SCGCQ00893220 - (Port_Complete) - Inconsistency in showing controller status between MSM and HII for Fake Flash errors
SCGCQ00865978 - (Port_Complete) - Pause for Password at boot time Enable/Disbale based on Boot Mode
SCGCQ00878512 - (Port_Complete) - HII-VD renaming truncates 15th character & allows for 16 characters,though only 15 supported
SCGCQ00882762 - (Port_Complete) - "Question value mismatch type!Press Enter" message is displayed while entering create virtual drive page
SCGCQ00884560 - (Port_Complete) - 13G Exception Screen thrown in uEFI environm
SCGCQ00873155 - (Closed) - Ctrl-R:Not able to lauch ctrl-R if 2 controllers, one with huawei and another with generic PnP ID is present.
SCGCQ00871350 - (Closed) - Handled the coverity defects.
SCGCQ00837424 - (Closed) - Storcli reports cache type as 'RW' instead of 'R' after R1 CC VD is degraded
SCGCQ00855701 - (Closed) - StorCLI does not find enclosures in multipath environment
SCGCQ00869436 - (Closed) - Include Partition table and GPT GUID check to detect OS/FS
SCGCQ00892967 - (Resolved) - Intruder: The size of the foreign config shown does not match with that after an import.
SCGCQ00893032 - (Closed) - With Liberator the Physical sector size of 512E drive is shown wrong
SCGCQ00853268 - (Resolved) - In EFI, Storcli displaying Bus Number ,Device Number and Function Number = 0 for all the controllers.
SCGCQ00868215 - (Closed) - Connector name field is displayed as & port 4-7 when a single ESM is connected in Multipath
SCGCQ00864200 - (Closed) - Checking in fix for resource leak
SCGCQ00867569 - (Closed) - storcli /c0 vall show is not listing CaC column when CC is not supported and displaying sCC with wrong value.
SCGCQ00870485 - (Closed) - EFI storcli is not working with intruder
SCGCQ00880534 - (Closed) - Invader 6.9 : Efi cli - Command fails with a hang when multiple controllers connected .
SCGCQ00860461 - (Closed) - In JBOD warning message all the drives are getting listed
SCGCQ00881720 - (Closed) - Foreign Config pop up scrollup/down does not respond
SCGCQ00860056 - (Closed) - "storcli show" shows wrong count for aso.
SCGCQ00868198 - (Closed) - Removing Phy information from Enclosure PD details.
SCGCQ00874381 - (Closed) - StorCLI: Memory Leak in function _available_memory_calc1.
SCGCQ00876796 - (Closed) - null pointer dereference
SCGCQ00892129 - (Resolved) - Most of the commands fail with "Invalid argument" error.
SCGCQ00884910 - (Closed) - StorCli Libmods 6.9 coverity fixes
SCGCQ00865108 - (Closed) - Ventura: storcli add vd fails with NVMe
SCGCQ00883409 - (Closed) - Storcli shows the wrong position of enclosures when they are connected in daisy chain with controller
SCGCQ00899384 - (Closed) - Buffer is not incremented when reading sector of the drive
SCGCQ00915164 - (Closed) - CTRL-H: Updating LargeIOSupport as per the new API changes
SCGCQ00889924 - (Closed) - Intruder Port2 and Port3 display are not handled in PD Mngt
SCGCQ00889771 - (Closed) - CTRL-H:Address Review comments
SCGCQ00881936 - (Closed) - Ctrl-R doesnot show the controller name above the menu
SCGCQ00850607 - (Closed) - added new command /c0 show swalilog equivalent to adpalilog
SCGCQ00834721 - (Implemented) - PNPs and support for 16 port 12G designs
SCGCQ00854633 - (Implemented) - Add details of pending FW images to StorCLI/sho adpinfo
SCGCQ00859740 - (Implemented) - RRB 88: Provide a more descriptive port enumeration (Libmods changes)
SCGCQ00893498 - (Closed) - LibMods: Add support to enable/Disable of Large IO Support - 1 MB IO
SCGCQ00893153 - (Closed) - CTRL-H: Add support to enable/Disable of Large IO Support
SCGCQ00854622 - (Closed) - Provide a more descriptive port enumeration
SCGCQ00850636 - (Closed) - Added support for flashing the FW on intruder and new Dev-ID's of Invader are added for EFI.
SCGCQ00828032 - (Implemented) - Add support to detect that an OS is installed on a JBOD
SCGCQ00853218 - (Implemented) - Add support to detect that an OS is installed on a JBOD
SCGCQ00844918 - (Implemented) - OEM requesting to do a WRITE VERIFY prior to flushing cache. This needs to be managed via CLI
SCGCQ00854626 - (Closed) - Provide a more descriptive port enumera
SCGCQ00904852 - (Port_Complete) - Checking-in changes for defect-SCGCQ00904794
SCGCQ00857695 - (Port_Complete) - Consistent Sorting of Controllers for End Users in Customer Facing Tools (EFI storcli)
SCGCQ00873795 - (Port_Complete) - CTRL-H: MonTask - line 243 in file ../../raid/1078int.c during rebuild
SCGCQ00854296 - (Port_Complete) - Add Pause For Password feature in CTRLH
SCGCQ00853654 - (Port_Complete) - Libmods implementation for WRITE VERIFY prior to flushing cache.
SCGCQ00878517 - (Port_Complete) - CTLR_R: PI-DG : After break mirror, data protection shown as "NA"
SCGCQ00900172 - (Port_Complete) - Added the iMR cutlass PNP id's(0x1000/0052h, 0x1000/0x0053h) to EFI controller explorer class.
SCGCQ00901264 - (Port_Complete) - MR 6.8: storcli reports legacy driver version when native driver is loaded for a Fury controller in ESXi 6.0
SCGCQ00853586 - (Port_Complete) - Get and Set Factory settings Failure
SCGCQ00850019 - (Port_Complete) - storcli /c0/eall/sall show smart command gives all zeros in the output
SCGCQ00849728 - (Port_Complete) - LibMOD:OEM requesting to do a WRITE VERIFY prior to flushing cache.
SCGCQ00878555 - (Port_Complete) - Ctrl-R is creating a smaller VD than specified when selecting a VD size in TB
SCGCQ00867486 - (Port_Complete) - Changed the Message for Hiding Boot VD Operation Status as per FW return error status.
SCGCQ00854279 - (Port_Complete) - Add Pause For Password feature in CTRLH
SCGCQ00893015 - (Port_Complete) - Inconsistency in showing controller status between MSM and Ctrl-R for Fake Flash errors
SCGCQ00874679 - (Port_Complete) - storcli doesnt display E252/E253 enclosure info on an 84016
SCGCQ00894487 - (Port_Complete) - Inconsistency in showing controller status between MSM and StorCLI for Fake Flash errors
SCGCQ00841286 - (Port_Complete) - Storcli : The bus error message is displaying for storcli /c0/eall/sall show smart comm

This download is valid for the products listed below:

- Intel Integrated RAID Module RMS3CC040
- Intel Integrated RAID Module RMS3CC080
- Intel RAID Controller RS3DC040
- Intel RAID Controller RS3DC080
- Intel RAID Controller RS3MC044
- Intel RAID Controller RS3SC008

About SATA / AHCI / RAID Controllers:

When enabled by appropriate software, the SATA controller (RAID or AHCI) is properly recognized by the system and all of its features are made accessible.

In addition to that, the computer will have the ability to read all adapter characteristics, such as model and manufacturer, and will also be able to manage physical disk drives through the controller’s interface.

If you wish to apply this package, all you have to do is to make sure that the current release is compatible with both your adapter model and your operating system, and then to get the downloadable software. Extract it if necessary, run the available setup, and follow the on-screen instructions for a complete installation.

When finished, remember to perform a system reboot to make sure that all changes take effect properly. Please remember that, even though other OSes might also be compatible, we do not recommend installing this software on platforms other than the specified ones.

That being said, click the download button, get the package and apply it on your computer. Moreover, constantly check with our website to stay up to date with latest releases. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Intel Drivers