Intel NUC RST Driver 14.6.0.1029 64-bit Download

Posted at December 22, 2024 by PCI-DB Team

Intel NUC RST Driver 14.6.0.1029 64-bit Description

Resolved Issues:

- BSoD 0x154 when run S4
- IAStorUI has stopped working" when click 'Manager' tab (Unit with M2 PCIe SSD) with no empty port available
- BSOD/Hung observed while resuming from CS with PCIe AHCI drives in remapped state
- Trim doesn't work on RAID0 on SATA SSD disks
- Recovery volume can’t be built in IRST when the secondary hard drives size is the same as the prim
- BSOD 0x9F occurred as reboot system after finishing Burn-in tool (4 hours) (add HDD R/W loading) test
- Cannot create RAID/SRT when RTD3 is enabled in BIOS
- SCSI Compliance Test 2.0 fails with NVMe disks
- Extremely low performance during copying file to RAID volume with PCIe AHCI
- RAID 1 going into 'failed' state during copying files to the volume.

This download is valid for the products listed below:

- Intel NUC Kit NUC6i3SYH
- Intel NUC Kit NUC6i3SYK
- Intel NUC Kit NUC6i5SYH
- Intel NUC Kit NUC6i5SYK

Known Issues:

- If use HDD larger than 1.3TB build recovery without show an error message when CSM disable.
- Intel RST driver v14.5.0.1059 cause BSOD Critical_Process_DIED during Sx
- BSOD 7E caused by iaStorA during cold boot stress test
- [Win10] SRT mode change to Enhanced, after setting Maximized mode and reboot PC.
- S4 hang black screen with certain NAS HDD under 2DR0 / 3DR5
- Error message display when run NvCacheScripts
- Removing the lowest numbered driver causes BSOD.
- RAID0 created using legacy OROM missing metadata on one of the drives
- PCIe NVMe SSD 2DR0 (2-disk RAID 0) performance lower than pass-through single SSD
- [RCfgSata][DOS] Partition table is not preserved when using the /U switch
- [RCfgsata][EFI][DOS]Incomplete serial number of drives is output when using the /ST switch
- [RST EFI CLI] EFI CLI config disk status does not show system disk information
- [rcfgsata.efi][SKL] Cannot boot to OS after creating RAID1 out of two data drives while preserving an MBR partition table
- DevSlpRegEditTool creates reg keys with invalid disk product_id
- rstcli.exe, rstcli64.exe allow to create recovery volume consisted of SATA and NVMe disks
- OS Spindown of matrix RAID volumes causes hang

About RST (Rapid Storage Technology):

Once Intel’s Rapid Storage Technology (RST) driver is applied, desktop and notebook systems will be able to manage the available storage (one or more drives) more easily.

And that’s not all you should expect: updating the RST version can also bring about improved storage performance, lower power consumption, faster boot times, quicker data reads, as well as several other changes.

As far as applying this release is concerned, simply make sure your system configuration is compatible with this package, run the available setup, and follow the on-screen instructions for a complete installation. In addition to that, don’t forget to perform a reboot to make sure that all changes take effect properly.

Even though other operating systems might be compatible as well, we do not recommend installing this package on platforms other than the specified ones.

With this in mind, click the download button, and get and apply the present version. Also, check with our website as often as possible in order to stay up to date with latest releases.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Intel Drivers