Gigabyte GA-Z77X-UD5H-WB WIFI (rev. 1.0) On/Off Charge Utility B11.1102.1 Download

Posted at December 18, 2024 by PCI-DB Team

Gigabyte GA-Z77X-UD5H-WB WIFI (rev. 1.0) On/Off Charge Utility B11.1102.1 Description

Specifications:

- CPU
Support for Intel Core i7 processors/Intel Core i5 processors/ Intel Core i3 processors/Intel Pentium processors/Intel Celeron processors in the LGA1155 package
L3 cache varies with CPU

- Chipset
Intel Z77 Express Chipset

- Memory
4 x 1.5V DDR3 DIMM sockets supporting up to 32 GB of system memory
Dual channel memory architecture
Support for DDR3 2400(OC)/1600/1333/1066 MHz memory modules
Support for non-ECC memory modules
Support for Extreme Memory Profile (XMP) memory modules

- Onboard Graphics
Integrated Graphics Processor:
1 x D-Sub port
1 x DVI-D port, supporting a maximum resolution of 1920x1200
The DVI-D port does not support D-Sub connection by adapter.
1 x HDMI port, supporting a maximum resolution of 1920x1200
1 x DisplayPort, supporting a maximum resolution of 2560x1600p

- Audio
Realtek ALC898 codec
Support for X-Fi Xtreme Fidelity and EAX Advanced HD 5.0 technologies
High Definition Audio
2/4/5.1/7.1-channel
Support for S/PDIF Out

- LAN
1 x Atheros GbE LAN chip (10/100/1000 Mbit) (LAN1)
1 x Intel GbE LAN chip (10/100/1000 Mbit) (LAN2)

- Expansion Slots
1 x PCI Express x16 slot, running at x16 (PCIEX16)
For optimum performance, if only one PCI Express graphics card is to be installed, be sure to install it in the PCIEX16 slot.
1 x PCI Express x16 slot, running at x8 (PCIEX8)
The PCIEX8 slot shares bandwidth with the PCIEX16 slot. When the PCIEX8 slot is populated, the PCIEX16 slot will operate at up to x8 mode.
1 x PCI Express x16 slot, running at x4 (PCIEX4)
PCIE Gen.3 is dependent on CPU and expansion card compatibility.
3 x PCI Express x1 slots
1 x PCI slot

- Multi-Graphics Technology: Support for AMD CrossFireX / NVIDIA SLI technology

- Storage Interface
Chipset:
2 x SATA 6Gb/s connectors (SATA3 0/SATA3 1) supporting up to 2 SATA 6Gb/s devices
4 x SATA 3Gb/s connectors (SATA2 2~5) supporting up to 4 SATA 3Gb/s devices
1 x mSATA connector
Support for RAID 0, RAID 1, RAID 5, and RAID 10
2 x Marvell 88SE9172 chips:
3 x SATA 6Gb/s connectors (GSATA3 6/7/8) supporting up to 3 SATA 6Gb/s devices
1 x eSATA 6Gb/s connector on the back panel supporting up to 1 SATA 6Gb/s device
Support for RAID 0 and RAID 1

- USB
Chipset:
Up to 2 USB 3.0/2.0 ports (available through the internal USB headers)
Up to 6 USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through the internal USB headers)
Chipset + 2 VIA USB Hubs:
Up to 8 USB 3.0/2.0 ports (4 ports on the back panel, 4 ports available through the internal USB headers)

- IEEE 1394
VIA VT6308 chip:
Up to 2 IEEE 1394a ports (1 port on the back panel, 1 port available through the internal IEEE 1394a header)

- Internal I/O Connectors
1 x 24-pin ATX main power connector
1 x 8-pin ATX 12V power connector
1 x PCIe power connector
5 x SATA 6Gb/s connectors
4 x SATA 3Gb/s connectors
1 x mSATA connector
1 x CPU fan header
4 x system fan headers
1 x front panel header
1 x front panel audio header
1 x S/PDIF Out header
3 x USB 3.0/2.0 headers
2 x USB 2.0/1.1 headers
1 x Clear CMOS jumper
1 x Trusted Platform Module (TPM) header
1 x power button
1 x reset button
1 x Clear CMOS button
1 x heatsink LED power connector
1 x BIOS Switch
Voltage Measurement Points

- Back Panel Connectors
1 x D-Sub port
1 x DVI-D port
1 x optical S/PDIF Out connector
1 x HDMI port
1 x DisplayPort
1 x eSATA 6Gb/s connector
4 x USB 3.0/2.0 ports
2 x USB 2.0/1.0 ports
1 x IEEE 1394a port
2 x RJ-45 ports
6 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Side Speaker Out, Line In/Mic In, Line Out)

- I/O Controller
iTE I/O Controller Chip

- H/W Monitoring
System voltage detection
CPU/System temperature detection
CPU/System fan speed detection
CPU overheating warning
CPU/System fan fail warning
CPU/System fan speed control
Whether the CPU/system fan speed control function is supported will depend on the CPU/system cooler you install.

- BIOS
2 x 64 Mbit flash
Use of licensed AMI EFI BIOS
Support for DualBIOS
PnP 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related GIGABYTE Drivers