Yamaha MTX Editor Utility 1.2.2/Firmware 1.20 Download

Posted at December 18, 2024 by PCI-DB Team

Yamaha MTX Editor Utility 1.2.2/Firmware 1.20 Description

This zip file includes the following software:

- MTX Editor V1.2.2
- MTX3 Firmware V1.20
- MTX5-D Firmware V1.20
- EXi8 Firmware V1.20
- EXo8 Firmware V1.20
- XMV series Firmware V1.20
- Dante Firmware Update Manager V1.4.7.1
- MTX5-D Dante Firmware V3.7.1.10-3.4.9.3-1.2.1
- XMV series Dante Firmware V3.7.1.10-3.4.9.3-1.2.1

Main Revisions and Enhancements

MTX Editor 1.2.2

- Solved a problem in which the channel names of odd channels were not displayed when you clicked the "ROUTER" tab when 2WAY was selected in the OUTPUT CHANNEL SETUP of the "MTX Configuration" dialog box.
- Solved a problem in which a Recall Filter was applied to a channel number, the software would apply the filter to the next lower channel when Recall Filter of a preset was set to the direct input channel (from CH17 to CH24) of MTX5-D.

MTX3 Firmware 1.20

- The choice of available subnet masks has been extended to increase network IP address range compatibility.
- Fixed a bug which caused unwanted data to be transmitted immediately following device boot up. Because of this fix, an external remote controller must now request the device status by using the [devstatus runmode] command, in order to establish communication.
- Solved a problem that caused the compressor of STIN2 to act in a stereo manner when the channel was set to MONOx2 in the “MTX Configuration” dialog box.
- Solved a problem when a log may be incorrectly retrieved in the "Get Log" dialog box of MTX Editor.
- Solved a problem when the IP SETTING of a device was set to PC mode (DIP switch 6 down), with an IP address other than 192.168.0.x , and then the IP SETTING was changed to UNIT ID mode (DIP switch 6 up), the IP address of the device was not set correctly to 192.168.0.(UNIT ID).

MTX5-D Firmware 1.20

- Now supports the MY4-AEC card.
- Now supports the DUGAN-MY16 card.
- The choice of available subnet masks has been extended to increase network IP address range compatibility.
- Now supports the “Identify device function” of Dante Controller.
- Fixed a bug which caused unwanted data to be transmitted immediately following device boot up. Because of this fix, an external remote controller must now request the device status by using the [devstatus runmode] command, in order to establish communication.
- Solved a problem when the SRC setting of the MY8-AE96S card was not saved to MTX5-D.
- Solved a problem that caused the compressor of STIN2 to act in a stereo manner when the channel was set to MONOx2 in the “MTX Configuration” dialog box.
- Solved a problem when a log may be incorrectly retrieved in the "Get Log" dialog box of MTX Editor.
- Solved a problem when the IP SETTING of a device was set to PC mode (DIP switch 6 down), with an IP address other than 192.168.0.x , and then the IP SETTING was changed to UNIT ID mode (DIP switch 6 up), the IP address of the device was not set correctly to 192.168.0.(UNIT ID).

XMV Firmware 1.20

- The choice of available subnet masks has been extended to increase network IP address range compatibility.
- Now supports the “Identify device function” of Dante Controller. (Dante models only)
- In addition to the existing -3dBFs input sensitivity setting, a -20dBFs option has been added for YDIF and Dante inputs. If -20dBFS is set from MTX editor, the digital input sensitivity will match that the analog input sensitivity.
- Fixed a bug which caused unwanted data to be transmitted immediately following device boot up. Because of this fix, an external remote controller must now request the device status by using the [devstatus runmode] command, in order to establish communication.
- Solved a problem when the Dante input patch of a XMV (Dante Model) was not correctly set if the UNIT ID of the device was changed.
- Solved a problem when the Dante input patch may be incorrect if synchronization was performed from MTX Editor and a XMV (Dante model) in the system was powered OFF, and then power to that XMV was turned ON.
- Solved a problem when the IP SETTING of a device was set to PC mode (DIP switch 6 down), with an IP address other than 192.168.0.x , and then the IP SETTING was changed to UNIT ID mode (DIP switch 6 up), the IP address of the device was not set correctly to 192.168.0.(UNIT ID).

EXi8/EXo8 Firmware 1.20

- The choice of available subnet masks has been extended to increase network IP address range compatibility.
- Fixed a bug which caused unwanted data to be transmitted immediately following device boot up. Because of this fix, an external remote controller must now request the device status by using the [devstatus runmode] command, in order to establish communication.
- Solved a problem when the IP SETTING of a device was set to PC mode (DIP switch 6 down), with an IP address other than 192.168.0.x , and then the IP SETTING was changed to UNIT ID mode (DIP switch 6 up), the IP address of the device was not set correctly to 192.168.0.(UNIT ID).

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Yamaha Drivers