MikroTik RouterOS SMIPS Firmware 6.32 RC 6 Download

Posted at November 2, 2024 by PCI-DB Team

MikroTik RouterOS SMIPS Firmware 6.32 RC 6 Description

What's new in 6.32rc6:

- trafflow - added support for IPv6 packets;
- switch - fixed port flapping on switch ports of RB750, RB750UP, RB751U-2HnD and RB951-2N (introduced in 6.31)
- ipsec - added compatibility option skip-peer-id-check;
- flash - fix kernel failure (exposed by 6.31);
- bridge firewall - add ipv6 src/dst addr, ip protocol, src/dst port matching to bridge firewall;
- RB911/RB912 - fix SPI bus lock after fast led blink;
- ipsec - fix potential memory leak;
- bridge firewall - vlan matchers support service tag - 0x88a8;
- ippool6 - try to acquire the same prefix if info matches recently freed;
- crs switch - allow to unset port learn-limit, new default is unset to allow more than 1023 hosts per port;
- x86 - fixed 32bit multi-cpu kernel support;
- chr - add hotspot,btest,traffgen support;
- revised change that caused reboot by watchdog problems introduced in v6.31;
- ipsec - use local-address for phase 1 matching and initiation;
- ipsec - fix transport mode ph2 ID ports when policy selects specific ip protocol on initiator;
- certificates -fixed bug where crl stopped working after a while;
- ip accounting - fixed kernel crash;
- snmp - fix system scripts get;
- hotspot - ignore PoD remote requests if no HotSpot configured;
- hotspot - fix kernel failure when www plugin aborts on broken html source;
- torch - add invert filter for src/dst/src6/dst6 addresses ;
- bonding - add min_links property for 802.3ad mode;
- snmp - get vlan speed from master interface;
- hotspot - fix html-directory path on small flash devices;
- mipsbe - make system shut-down work again;
- lcd - fixed parallel port LCD display support on multi-cpu x86;
- bridge - fixed use-ip-firewall-for-vlan in configurations with multiple bridges;
- ipv6 - fixed DHCP-PD client skips some steps when renewing lease;
- upnp - fixed protocol port selection for upnp protocol communications;
- firewall - fixed limit and dst-limit options.

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related MikroTik Drivers