Intel NUC RST Preinstall Driver 14.6.0.1029 Download

Posted at December 22, 2024 by PCI-DB Team

Intel NUC RST Preinstall Driver 14.6.0.1029 Description

Resolved Issues:

- BSoD 0x154 when run S4
- IAStorUI has stopped working" when click 'Manager' tab (Unit with M2 PCIe SSD) with no empty port available
- BSOD/Hung observed while resuming from CS with PCIe AHCI drives in remapped state
- Trim doesn't work on RAID0 on SATA SSD disks
- Recovery volume can’t be built in IRST when the secondary hard drives size is the same as the prim
- BSOD 0x9F occurred as reboot system after finishing Burn-in tool (4 hours) (add HDD R/W loading) test
- Cannot create RAID/SRT when RTD3 is enabled in BIOS
- SCSI Compliance Test 2.0 fails with NVMe disks
- Extremely low performance during copying file to RAID volume with PCIe AHCI
- RAID 1 going into 'failed' state during copying files to the volume.

This download is valid for the products listed below:

- Intel NUC Board D34010WYB
- Intel NUC Board D54250WYB
- Intel NUC Board NUC5i3MYBE
- Intel NUC Board NUC5i5MYBE
- Intel NUC Kit D34010WYK
- Intel NUC Kit D54250WYK
- Intel NUC Kit NUC5i3MYHE
- Intel NUC Kit NUC5i3RYH
- Intel NUC Kit NUC5i3RYK
- Intel NUC Kit NUC5i5MYHE
- Intel NUC Kit NUC5i5RYH
- Intel NUC Kit NUC5i5RYK
- Intel NUC Kit NUC5i7RYH

Notes:

- Known Issue is defined as a potential RST issue that has been replicated internally by the Rapid Storage Technology team but has not been root caused to be an RST defect.
- The RAID OROM & UEFI version for this release is 14.6.0.2285, the driver and user interface version is 14.6.0.1029. The Devslp tool is posted under the CLI tool components on VIP kit.
- RST 14.6 release enables support for new platforms & features (includes legacy support for platforms and features supported in RST 14.5): Skylake mobile U/Y Corporate Platform, SKL-U 2+3e Platform and Support for NVMe API
- Issue with detecting PCIe storage when remapping is enabled on HM170/QM170 is fixed with the Pre-OS build 14.6.0.2285 included with PV package.
- No RST support for PCIe storage devices in AHCI mode.

Known Issues:

- If use HDD larger than 1.3TB build recovery without show an error message when CSM disable.
- Intel RST driver v14.5.0.1059 cause BSOD Critical_Process_DIED during Sx
- BSOD 7E caused by iaStorA during cold boot stress test
- [Win10] SRT mode change to Enhanced, after setting Maximized mode and reboot PC.
- S4 hang black screen with certain NAS HDD under 2DR0 / 3DR5
- Error message display when run NvCacheScripts
- Removing the lowest numbered driver causes BSOD.
- RAID0 created using legacy OROM missing metadata on one of the drives
- PCIe NVMe SSD 2DR0 (2-disk RAID 0) performance lower than pass-through single SSD
- [RCfgSata][DOS] Partition table is not preserved when using the /U switch
- [RCfgsata][EFI][DOS]Incomplete serial number of drives is output when using the /ST switch
- [RST EFI CLI] EFI CLI config disk status does not show system disk information
- [rcfgsata.efi][SKL] Cannot boot to OS after creating RAID1 out of two data drives while preserving an MBR partition table
- DevSlpRegEditTool creates reg keys with invalid disk product_id
- rstcli.exe, rstcli64.exe allow to create recovery volume consisted of SATA and NVMe disks
- OS Spindown of matrix RAID volumes causes hang

About SATA / AHCI / RAID Preinstall Drivers:

Download this package if you intend to switch the SATA settings between available modes (AHCI, RAID, or IDE) after an operating system has been installed.

Remember that if you modify these settings without applying the proper files, the OS will not be able to boot until requirements are met or changes are reverted.

As for the installation method, it would be best if you refer to the manufacturer’s update guide, read all the steps, and initiate this task only when you have completely familiarized yourself with the procedure.

Even though other platforms might also be compatible with this release, we strongly recommend that you apply the driver only on specified operating systems in order to successfully perform the installation. If a failure occurs, the computer could suffer serious malfunctions.

With these in mind, if you wish to modify the SATA settings according to the mode highlighted in this version, click the download button and make the desired changes. Visit our website as often as possible to stay up to date with the latest releases. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Intel Drivers