Gigabyte GA-EP35-DS4 Realtek LAN Driver 5.736.0728.2009 for XP Download

Posted at November 21, 2024 by PCI-DB Team

Gigabyte GA-EP35-DS4 Realtek LAN Driver 5.736.0728.2009 for XP Description

CPU   

1. Support for an Intel Core 2 Extreme processor/ Intel Core 2 Quad processor/Intel Core 2 Duo processor/ Intel Pentium processor Extreme Edition/Intel Pentium D processor/ Intel Pentium 4 processor Extreme Edition/Intel Pentium 4 processor/ Intel Celeron processor in the LGA 775 package
(Go to GIGABYTE's website for the latest CPU support list.)
2. L2 cache varies with CPU
3. 1600 (O.C.)/1333/1066/800 MHz FSB

Chipset   

1. North Bridge: Intel P35 Chipset
2. South Bridge: Intel ICH9R

Memory   

1. 4 x 1.8V DDR2 DIMM sockets supporting up to 8 GB of system memory
2. Dual channel memory architecture
3. Support for DDR2 1200 (O.C.)/1066/800/667 MHz memory modules

Audio   

1. Realtek ALC889A codec
2. High Definition Audio
3. 2/4/5.1/7.1-channel
4. Support for DTS (dts NEO:PC)
5. Support for S/PDIF In/Out
6. Support for CD In

LAN   

1. Realtek 8111B chip (10/100/1000 Mbit)

Expansion Slots   

1. 2 x PCI Express x16 slots (The PCIE_16_1 slot supports x16; the PCIE_16_2 supports x4.)
2. 3 x PCI Express x1 slots (share with the PCIE_16_2 slot)
3. 2 x PCI slots

Form Factor   

1. ATX (305 x 244mm)

Storage Interface

South Bridge:
1. 6 x SATA 3Gb/s connectors (SATAII0, SATAII1, SATAII2, SATAII3, SATAII4, SATAII5) supporting up to 6 SATA 3Gb/s devices
2. Support for SATA RAID 0, RAID 1, RAID 5, and RAID 10

GIGABYTE SATA2 chip:

1. 1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices
2. 2 x SATA 3Gb/s connectors (GSATAII0, GSATAII1) supporting up to 2 SATA 3Gb/s devices
3. Support for SATA RAID 0, RAID 1, and JBOD

iTE IT8718 chip:

1. 1 x floppy disk drive connector supporting up to 1 floppy disk drive

IEEE 1394   

1. T.I. TSB43AB23 chip
2. Up to 3 IEEE 1394a ports (2 on the back panel, 1 via the IEEE 1394 bracket connected to the internal IEEE 1394 header)

USB

1. Integrated in the South Bridge
2. Up to 12 USB 2.0/1.1 ports (8 on the back panel, 4 via the USB brackets connected to the internal USB headers)

Internal I/O Connectors   

1. 1 x 24-pin ATX main power connector
2. 1 x 8-pin ATX 12V power connector
3. 1 x 4-pin PCIe 12V power connector
4. 1 x floppy disk drive connector
5. 1 x IDE connector
6. 8 x SATA 3Gb/s connectors
7. 1 x CPU fan header
8. 2 x system fan headers
9. 1 x power fan header
10. 1 x North Bridge fan header
11. 1 x front panel header
12. 1 x front panel audio header
13. 1 x CD In connector
14. 1 x S/PDIF In header
15. 1 x S/PDIF Out header
16. 2 x USB 2.0/1.1 headers
17. 1 x IEEE 1394a header
18. 1 x parallel port header
19. 1 x serial port header
20. 1 x power LED header
21. 1 x chassis intrusion header

Back Panel Connectors   

1. 1 x PS/2 keyboard port
2. 1 x PS/2 mouse port
3. 1 x coaxial S/PDIF Out connector
4. 1 x optical S/PDIF Out connector
5. 8 x USB 2.0/1.1 ports
6. 2 x IEEE 1394a ports
7. 1 x RJ-45 port
8. 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker Out/Line In/Line Out/Microphone)

I/O Controller   

1. iTE IT8718 chip

H/W Monitoring   

1. System voltage detection
2. CPU/System temperature detection
3. CPU/System/Power fan speed detection
4. CPU overheating warning
5. CPU/System/Power fan fail warning
6. CPU fan speed control

BIOS

1. Supports DualBIOS Plus
2. 2 x 8 Mbit flash ROM
3. Use of licensed AWARD BIOS
4. PnP 1.0a, DMI 2.0, SM BIOS 2.3, ACPI 1.0b.

Unique Features   

1. Support for @BIOS
2. Support for Download Center
3. Support for Q-Flash
4. Support for EasyTune
5. Support for Xpress Install
6. Support for Xpress Recovery2

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related REALTEK Drivers