Peplink Pepwave MAX HD2 HW3 Router Firmware 7.0.2 Download

Posted at December 3, 2024 by PCI-DB Team

Peplink Pepwave MAX HD2 HW3 Router Firmware 7.0.2 Description

​​Important​ ​Notices:

For​ ​Firmware​ ​7.0.1​ ​Onwards
- PepVPN​ ​Route​ ​Isolation​ ​is​ ​Not​ ​Backwards​ ​Compatible:​ ​If users are using PepVPN Route Isolation, they should upgrade all the devices in the network to 7.0.1 or 6.3.4.

For​ ​Firmware​ ​7
- PepVPN​ ​Firmware​ ​Compatibility​ ​Change​: Devices running Firmware 7 will only form PepVPN connections with devices running Firmware 6.1 or later. Firmware 6.0 or earlier is deprecated.
- Firmware​ ​Downgrade​ ​is​ ​Unavailable​ ​for​ ​the​ ​BR1,​ ​BR1​ ​ENT,​ ​BR1​ ​Slim,​ ​and​ ​Transit: Please note that once Firmware 7 is installed on those, it will not be possible to downgrade to Firmware 6 or below. Dual-boot with older Firmware is still supported, but each Firmware slot will not accept earlier Firmware once it contains Firmware 7.
- After​ ​Partitioning​ ​a​ ​MediaFast​ ​Router,​ ​Running​ ​Previous​ ​Firmware​ ​will​ ​Completely Clear​ ​the​ ​Cache:​ ​Please note that once you create partitions on any MFA router, running 6.3.3 or below will cause the router to clear the entire cache.

Feature​ ​Improvements:

- [DHCP]​ ​Added option 82 information added to client DHCP discovery packet. No need to enable DHCP relay. This option can be enabled only if L2VPN is configured.
- [PepVPN]​ ​In PepVPN advanced options, the "Suspension Time after Packet Loss" can now be set to 0 to disable the suspension time.
- Compatible with All​ ​Balance​ ​/​ ​MediaFast​ ​/ MAX​ ​models
- Compatible with Surf:​ ​SOHO

- [AP​ ​Controller]​ The Lite version of the AP Controller now supports SSID Guest Protect for both local AP and external AP.
- Compatible with Balance:​ ALL
- Compatible with MAX:​ 700, HD2, HD2 Mini, HD2 IP67, Transit, HD4
- Compatible with MediaFast:​ All

- [Data​ ​Roaming]​ ​Added the ability for users to select which countries to enable data roaming using the mobile country code (MCC).
- [SIM​ ​Bandwidth​ ​Pool]​ ​Define multiple SIM pools for each IC2 group, and set the pool's bandwidth quota limit. Email notifications are sent once quotas are reached. Please note that this feature requires InControl2 to function.
- Compatible with Balance:​ 30 LTE
- Compatible with MAX:​ ​All​ ​models​ ​except the​ ​700​ ​and​ ​OTG
- Compatible with MediaFast:​ ​HD2, HD4

- [Surf​ ​SOHO]​ The Surf SOHO now supports WAN IP Passthrough
- Compatible with Surf:​ ​SOHO

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Peplink Drivers