Intel iMR 3108 ROC Hardware RAID Firmware 24.2.1-0021 Download

Posted at December 21, 2024 by PCI-DB Team

Intel iMR 3108 ROC Hardware RAID Firmware 24.2.1-0021 Description

Versions:

- Firmware 4.220.40-3267
- UEFI_Driver 0x06030501
- Hii 03.05.11.03
- BIOS 6.14.05.0
- Ctrl-R 5.03-0005
- BootBlock 3.02.00.00-0000
- NVDATA 3.1310.00-0070
- FCODE 4.16.08.00
- PCLI 1.07.05
- ROMENV 1.09

This download is valid for the product listed below:

- Intel RAID Controller RS3WC080

Fixes:

- Battery learn cycle continues to more than one cycle even FW has marked it as bad in previous reboot
- DIS mismatch while running system reboot script with dirty data in DDR
- Optimize onfi descriptor setting for offload
- FW crash while launching Ctrl+R
- Assertion failure in double DIP power cycle test case
- Elapsed time of Patrol Read in tty log is incorrect
- Elapsed time of Reconstruction is incorrect
- Firmware not taking "SMARTerEnabled" from NVDATA
- Rebuild triggered on an incompatible blocksize PD
- Upgrade 3108 MR FW failing
- PD erase does not work with SATA SSDs
- Diagnostics failed after Drives goes to shield state
- The DQlog.bin is getting corrupted after restarting the service of MRDiag
- protect the removal of the device when the device is still under initialization
- BIOS is not getting updated with the DISM progress
- Running out of free entries in task list due to recursive addition of tasks
- Wrong information of PD erase progress is shown by the firmware.
- DM_DISM_LOG_SENSE state is not present in DISM
- PI enabled VD is importing successfully even though "prevent PI Import" option is enabled
- Change the CRC filed size
- Fix the learn issue at powerup
- LSI_MR Controllers fails to set "FACTORY SETTINGS"
- VD's switch from Write Back with BBU to Write Through when an OCR is issued and BBU gets disabled.
- Fix scheduling of hostspare correctly
- seen DC error while running io's on 6.2 in Dev pull-push setup
- chaos fails on R6 VD after importing failed R5 VD and one of R1 CacheCade drive
- Defect fix for MSM does not show Create cachecade option
- To fix task list overflow issue on max config setup
- FW throws "MPT_LogDiscoveryErrors: SAS_TOPOLOGY_MAX_TOPO_PHYS_EXCEED" when connect 2 in multi-path
- Assertion failure in ../../raid/raidpci.c at line 10522
- Read VPD error message on 3108
- Configurable drives count in iMR reflected wrongly to applications
- wrong error code displayed and wrong error message for copyback command
- FW hits to MonTask: while running enclosure power cycle with 4K drives
- Issue with supercap energy calculations
- modify scap energy calculation
- directly attached SATA drive is not detected by controller
- Dual Context to Single Context switching does not toggle when Cobra expanders are cascaded with EDFB enabled PHY's.
- Defect fix for Montask observed while installing OS on JBOD
- Controller Hangs during execution of Storcli command ''/c0 delete termlog''
- Battery retention test failure during continuous loop test when there was power failure during erase
- Battery Enable (BBE) is asserted even when BBU/Supercap not present or even when all LDs are in WT mode
- TM timeout during enclosure pull while running heavy IO
- Learn is not completing at powerup
- 3TB Seagate PD size being reported as 2TB in Apps/Firmware
- Controller Reset due to Fatal Error with RAID6/60 configuration
- Elapsed Seconds displayed in firmware logs for background operations progress is improper
- Kill adapter observed while running IOs on JBODs and VDs
- CME handling of Invader
- Issue with Global Hot Spare assignment
- Drives connected through enclosure showing wrong slot numbers.
- Issue with MR 24.1.1-003 with JBOD Mode enabled
- (null) noticed while PD pull-push testing.
- SMPpassthru is not happening through storlib.
- System Reboots after issuing the OCR and kernel panic is observed
- on breaking multipath while drives are spinning up results in montask
- Initialize invalid interrupt as part of intInitialize function
- OEM server hangs after enabling EKM and rebooting.
- Associating cachecade VD to a secured VD from Storcli does not fail.
- Offload fails after corrupting BMT1 and BBT 2 address location
- Adding the log event corresponding to ER SCGCQ00493492
- BGI kicks in on 5R5 but shows no progress at any point of time.
- Defect fix for Unable create R0 in HII with 4K drives
- FW-FW hit 'MonTask: line 243 in file ../../raid/1078in' while issuing OS reboot command on 9340 controller
- CPLD input GPIO 21 driving when supercap is present and not present
- Pinned cache gets flushed even after memory battery problem occurs.
- VD erase restarts instead of resuming after reboot.
- Fix the cset issue
- Cache Memory Size of controller Information is ZERO
- Data Corruption observed while running FPIO on VDs; making-breaking multipath in overnight loop.
- Config loss after OCR during creation of config - when the drives are still spinning up
- Added an event to notify the user when command times out on PD
- FDE/SED drives does not reflect as FDE/SED drives.
- "Corrected medium error" event is logged for uncorrectable medium errors during PR
- To declare block bad at the earliest for the safer side the number of error correction bits shall be reduced
- Re-enable EKMS for OEM
- System reboots continuously after flashing Firmware in Solaris _11
- MonTask: line 7193 in file ../../bbu/onfi.c
- Kill adapter observed on large setup on enquiring Controller properties while drives spinning up from powersave.
- coverity tool reported issue 13545(Wrong sizeof argument)
- restore and flushing cache to PD are not reliable when 1st image of NF mem is corrupted
- Firmware is allow to create slices in cachecade drivegroup using SMIS utility.
- EKMS feature for OEM is disabled
- max temperature bytes read from VPD is should be swapped before using
- MR_6.2_DISM: FW hung due to DISM discovery failure on pulling the enclosure cable on reboot after running adpbattest.
- Controller alarm continues to beep after transitioning VD from degraded to optimal state.
- Handle OEM fault LED behavoir
- MR6.2_iMR_fury_DM_Issue_TUR
- In enclosure management page for DELL ,it shows some junk data in HII
- Controller Reset due to Fatal Error with RAID6/60 configuration
- CME logic using overlaid fields in c->rec
- Montask appears on running IO's on 64VD's while changing LD policies
- Enable OCR by default on GCA builds
- MR: on FW init, controller post adapter base port missing
- Invalid "Elapsed Seconds" value for FGI
- Rebuild and Consistency Check aren't progressed when it is executed by CTL+R
- Latest API changes in mr.h breaks FW compilation in mrdebug.c
- Build Issue using GNUmakefile for MR and iMR
- Storcli command to reset the boot ld on controller fails
- boot block compile fails because of an erroneous macro definition
- DATA TLB error faced while powercycle the enclosure during controller initialization
- foreign import fails if degraded VD is present in import
- Toolbox Console Text Display Tool
- Porting of the PR "spin up changes to accommodate multiple power domains simultaneously" to Invader.
- Validate the requested blocks for SCSI VERIFY commands on RAID volumes
- IOCInit multiple Reply Descriptor Post Queue addresses
- Firmware Change for Pre-boot management tool & boot capability for SPARC
- add reserved fields to IO Unit Page 7 for future use
- Disable thermal throttle changes
- Identifying the DDR, ONFI flash and SCap combination
- SGPIO back plane requires ramdon slot number support.
- Increase PCIe Receiver Margin
- Increase margin in PCIe Rx Serdes
- obsolete SAS IO Unit Control _TRANSMIT_PORT_SELECT_SIGNAL
- obsolete "Limit SATA max rate to 1.5 Gbps"
- Debug Queue Implementation and Support as part of enhanced MR Diagnostic support
- Increase the support for 32 slots
- Add Critical event in FW to indicate that an INIT operation was halted due to reboot or other failure
- Update code to modify GG and VPD at powerup
- Implement throttle mechanism to prevent thermal run away
- Change hash algorithm for cache row hash from a bit mask to a modulo
- DIS feature
- Signed images for FWDownload
- Don't interpret the cachecade BVD flags if the volume is created with old FW which does not support cachecade.
- Code-review action item for removing and updating names for AEN dism.
- Patrol Read - no progress
- WB Logical disks are moving to WT after corrupting BMT1,BBT1 and reboot.
- Deep Learn is not invoked in new battery, when the system is reboot before the first learn completes
- Transparent Learn Cycle is rescheduled even though it is not completed
- TFM error handling : Cache policy change for WB to WT if supercap is faulty
- Intermittent SEP errors on iMR and MR controllers
- When Cachecade LD is deleted invalid LD details is shown in the Cachecade size changed event.
- Hotspare Recovery Doesn't Start after Inserting Failed Drives
- FW sending wrong configuration data during boot msg pending state
- Upgrading from Software RAID to 9260-8i causes Alarm to sound
- ONFI_BBM Dev test build: FwTermLog does not preserve information before powerup.
- iMR TB Data loss when reconstructing from 1 drive R0 to 2 drive R1 with reboot
- incorrectly uses a slot offset value to enumerate HDD.
- In case of a certain OEM iMR shows R5 enabled.
- MSM log warning: Controller booted in headless mode with errors
- Set the Recovery mode page (WriteRetryCount and recoveryTimeLimit)
- If VD is secured while reconstruction is going on does not stay secured once reconstruction is done.
- SEAGATE hotspare drives remain spun up on LSI FW 12.12.0-0079
- Firmware is not updating recovery timer as intended
- Call DDF_discardInvalidPds only if DS3 is enabled
- LSI_MR Controllers fails to set "FACTORY SETTINGS"
- Controller Reset due to Fatal Error with RAID6/60 configuration
- VPD output of lspci –vvxxx showing [RV] Reserved: checksum bad, 86 byte(s) reserved
- Multi-stripe size in each raid level of R1,r5,r6 with SAS, DIF, 4K pinned cache offline vd import cause Montask
- Remove memory module on MR controller to downgrade to iMR does not work
- HII critical message form/Extra character "r" with configuration not supported critical message.
- Fw defect in PdStateSet()
- Controller Reset due to Fatal Error with RAID6/60 configuration
- Correct how the SCL high and low period values are calculated for the I2C to run at 400Khz
- For new spin up code get persistent devId for drives that are connected via internal back plane.
- Controller Reset due to Fatal Error with RAID6/60 configuration
- Drive security mode switching in MSM
- Unable to create another Virtual Drive when pulling first drive (degrading) in partial Virtual Drive where all drives are configured
- Baseboard Management Controller (BMC): STP passthru command failure
- External Key management security for iMR
- Re-keying a controller with External Key Management(EKM) security enabled, results in a corrupted key ID.
- Performing an online firmware update or Online Controller Reset(OCR) on a controller with External Key Management(EKM) enabled, results in all secured drives marked as foreign.
- MR 4K Validation : 4K VD assigned to 512K CacheCade
- Re-keying in External Key Management mode followed by disabling security and enabling LKM results in a bail out while creating a Virtual Drive
- VD goes offline when we start reconstruction on 32 Drive R0 VD
- Raise priority of pci config trap interrupt to critical
- Not seeing the correct Boot Message when the connection to the External Key Management server is down
- Switching to Local Key Management Mode(LKM) after a rekey in External Key Management(EKM) rekey without rebooting results in HII saying key incorrect but Firmware says key was created.
- On a controller with Local Key Management(LKM) enabled, user is asked to enter the security key to unlock and import a foreign, locked and External Key Management(EKM) enabled drive.
- FwTermLog does not preserve information before powerup.
- Implement I2C Slave Address for Sideband Management
- Defect Fix for VPD and inquiry callback issues in DISM
- spin up tracker dequeue is not handled for case in which TUR error happens even after MAX retries
- Too many unexpected sense AEN raised by CC during CME recovery on R5
- Too many unexpected sense AEN raised by CC during CME recovery on R5
- Fix GNU make file compilation
- Routines to inject bit error in NF and ecc error in DDR for ONFI
- Mismatch in LD id and target ID during set/reset boot device
- Mismatch in LD id and target ID during set/reset boot device
- Adding test routine for the bad block loop test for PR SCGCQ00423195
- SMART poll needs to issue log sense with page control set to current/ cumulative value
- FW breaks if wrong security key is entered
- on breaking the multipath in loop while drives are spinning up will result in montask
- FW hangs while creating 64 VDs on the controller with SLES11 SP2 PPC64
- While running reconstruction from R1 to 4 drive PRL11 with IO,FW hits to MonTask: line 1270 in file ../../raid/1078dm
- Static analysis tool defect
- Static Analysis Tool defects
- CLI Reporting of TMM VPD
- Rebuild triggered on an incompatible blocksize PD
- Issue with Global Hot Spare assignment
- Elapsed time of Reconstruction is incorrect
- Elapsed time of Patrol Read in tty log is incorrect
- "Corrected medium error" event is logged for uncorrectable medium errors during PR
- Increase margin in PCIe Rx Serdes
- Increase PCIe Receiver Margin
- Liberator Card loses its boot VD after many reboots
- Cache policy of Virtual Drives(VD) does not change to Write Through(WT) mode even after detecting a bad supercap.
- RAID configured on PD been erased with Normal or Thorough will lost after system reboot/reset
- Defect fix for kenel panic with iMR Fury with Free BSD driver
- Hitting montask line 1930 in file ../../bbu/onfi.c while running FP IO's on degraded VD's
- Cachecade configurations could not be created.
- Deep learn doesn't start when it is requested during relaxing.
- Write policy changed from WT to WB when the battery/Supercap is declared as bad
- Firmware crash seen while doing continuous sas cable pull
- Invalid "mode select(Page=0a)" issued during disk initialization phase.
- Defect fix for Montask observed while installing OS on JBOD
- Firmware returns asc value as 0 when failing IOs with medium errors
- display BMU fw version in battery design info
- Break Mirror for R10 should not be allowed
- Medium error correction event is not logged during CC
- 9240-4i on BCM RX67Q-6S motherboard is not getting required memory resources on boot
- foreign import fails if degraded VD is present in import
- L2/L3 cache error on reboot
- search for one wire devices prints are masked after the boot
- VPD info can't be retrieved for OEM enclosure
- If a BOOT Passphrase is enabled with SafeStor "MegaCli adpbios dsply a0" will display "BIOS will Stop on error" even if any other mode is set.
- Profile based VD creation - [Partial RAID options blocked until system reboot]
- Hard coded values should be removed in TFM module
- Fix repeated prints issue
- A data TLB error occurs when the External Key Management Server(EKMS) is down and drive security is changed from External Key Management(EKM) mode to Local Key Management(LKM) mode.
- HII & Ctrl-R: BGI operation still running on RAID0 VD even after PI protection disabled
- Getting a non informative message when trying to import a Virtual Drive after a re-key without reboot
- Deep learn will not start immediately when Relative State of Charge (RSOC) of battery is equal to 95%.
- Raid configuration loss after reboot - PDs in POWERSAVE
- Fix the learn issue at powerup
- Faulty protocol used for changing the Disk Write Cache Policy
- on breaking the multipath in loop while drives are spinning up will result in montask
- FW- FW hangs while creating 64 VDs on the controller with SLES11 SP2 PPC64
- Static Analysis Tool defects
- Static Analysis Tool defects
- Enabling DQ support bit in FW
- The restore successful and unsuccessful prints to be handled properly
- not enough bs found during double Dip power cycle Test
- Montask in divert.c seen when injecting 64K consecutive errors on R0 VD, Patrol Read running in background.
- Single image support for ONFI
- Assertion failure (not enough BS found) in double DIP power cycle test case
- DC observed upon performing OCR on a degraded R1 (AWB).
- 9260-8i(SAS2108) hitting OOB SRAT timeout for a long time causing OOB commands to fail
- modify scap energy calculation
- wrong error code displayed and wrong error message for copyback command
- Bad or Missing TMM boot message is changed to Critical error
- 9260-16i's drive locate/fault LED header doesn't work
- MR Controller does OCR due to Temp Buffer overflow
- The Firmware does not change the Virtual Drives's from Write Through to Write Back after a battery manual learn cycle is complete
- SLES 11.3 x64 Halts when Loading Kernel During Warm Reboot Stress
- Initialize invalid interrupt as part of intInitialize function
- Switching the security mode from External Key Management(EKM) to Local Key Management(LKM) on iMR controller will result in a corrupted controller key.
- SMART poll needs to issue log sense with page control set to current/ cumulative value
- Static Analysis Tool defects
- Power removal of enclosure FW hits to MonTask: line 4056 in file ../../bbu/onfiBBM.c
- Multiple interposer drives will not be detected by MegaRAID firmware.
- Infinite retry happens on Test Unit command when HDD didn't respond to TU command during the initialization.
- Secondary RAID key data page read failure 6 seen on some controllers and key vault combination
- StorCLI_F showed firmware download failed but really took
- Assertion failure in ../../raid/raidpci.c at line 10522
- FW Crash when using SCSI Passthrough SCSI_READ_10(0x28) to read 512 bytes on a RAID5 Native 4K drive.
- When pinned cache present VD property not changing from WB to WT.
- PDs go online without VD created & App doesn't allow any VD creation on passing a wrong parameter in Spanned VD.
- Customer is hitting an ECC error
- Invader: Cache Memory Size of controller Information is ZERO
- Incorrect variable type in MR Read/Modify/Write path
- StorCLI_F showed firmware download failed but really took
- cache restore failure message displayed though cache restore was successful
- System hanged after pulling out drives from a 8Raid-6 array during OCR in Debian OS
- Change SES Green/Amber LED behaviour for OEM ACHILLES JBOD enclosure.
- FW breaks if wrong security key is entered
- While executing path-failover test with an SATA-SSD drive behind an interposer, the device is marked failed.
- Card Running iMR Machine Checks when Requesting Host Memory
- iMR FW update caused card to FW fault state and card cannot boot to OS.
- system black screen during S1 Sleep test
- Firmware Crash during Controller StartUp when large number of drives are connected
- Block IO tests from SCT IHV test suite failed
- Disable Debug print in UEFI Driver
- Not able to boot into BIOS boot menu
- In IsValidHandle() - Free the buffer if status is not EFI success for LocateHandle
- Memory Leak issue in UEFI driver when reconnect happens
- Remove private GUID and use EFI_KMS_PROTOCOL_GUID defined in UEFI 2.3.1 spec
- Disable Debug print in UEFI Driver
- UEFI hang when SATA is connected
- UEFI hang when SATA is connected
- UEFI Driver should calculate checksum before setting bios data (MR_BIOS_DATA)
- Uninstall HII CAP and Driver Health formset if platform calls Start again without calling GetHealthStatus
- 9240/9260/9270 UEFI driver issue with RD640/RD440 platforms when user having 2TB or 4TB VD
- 9240/9260/9270 UEFI driver issue with RD640/RD440 platforms when user having 2TB or 4TB VD
- Follow UEFI Spec on interpreting In and Out Transfer Length that upper layer sends
- Block IO tests from SCT IHV test suite failed
- Follow UEFI Spec on interpreting In and Out Transfer Length that upper layer sends
- Allow user to edit VD size (that is free form input) as it is cumbersome to modify the size using +/-
- Save and Restore Configuration – MR
- Transition a Thunderbolt MR controller to run in iMR mode = Controller fail in HII After Memory removed
- When controller is in safe mode the PD menu displays inaccurate text and hangs when clicking a PD
- HII\EKM-LKM without reboot should show proper message
- HII cannot assign partial space less than 1 GB
- fixing code review defects (AIM version + UCM GUID + deallocation)
- Profile Based Raid1 Creation fails as invalid arguments
- Naming inconsistency in option present in Create VD and Create VD - Advanced
- condition checking is not right
- Allows user to select EKM mode when supportEKM is set to 0
- Using 84 PD encl when clicking on HW, Advanced then Enclosure Management, it completely freezes the system
- Allow user to select RAID level when controller has other VD + error handling
- Enter security key for locked drives screen, press down to get to OK, OK will show up again on right
- unable to show UF003 as well the first two forms + XML special character handling
- fixing memory leak of 128 drive enclosure implementation
- Able to select EKM even when the EKM FOD key is removed from the system.
- Drop down option to set phy linkspeed tp 12 Gbps in HII browser is not available.
- Save and Restore Configuration - MR w/ Premium Features (SED and Cachecade)
- Issues when trying to change EKM security key from change security key option.
- EKMS is down but it is still possible to select drive security in MSM and HII during creation.
- Going from LKM to EKM asks for a Current Security key Identifier and Security key.
- Update the latest API change in HEFU
- UCM Phase 1: Typo "Clear Configuration" -> "Clear Configuration"
- EXPAND operation fails in HII for prl11
- Streamline the usage of max PD in limited configuration path (alias UCM)
- Help content for Free space in Select Drive group is inappropriate
- UCM Simple Configuration: Allow Clear Config always + Suppress Checkbox (Uf002.PDs) when VD count is >0
- added a while loop and take care of the multiple PD Groups scenario.
- AIM (Agentless Inventory Manager) Issues
- Typos in help content for profile VD for Write Policy
- Profile based VD creation path incorrectly showing protect VD/secure VD checkbox when user clicks on drive selection criteria
- config using 8PDs/16 partial VDs and all stripe sizes and HSPs does not restore
- After creating a VD with UCM tool the manual configuration PD section still shows configured PDs as UG, and duplicates
- Controller not seen in HII Browsercan after switching from EFI WebBIOS
- Checking the Enclosure Management settings in HII causes the system to reboot.
- Request to support 128 drives wihin single enclosure
- UCM Phase 2 support
- (Implemented) - Create a formset with classGUID that customer has provided.
- Request to change the help content for write policy in create VD form
- Obtain the Physical Slot number from the PCI Bridge to which the Controller is connected.
- System hang observed when the "PdInfo.userDataBlockSize" is set to 0
- HII cannot assign partial space less than 1 GB
- RSOD during POST after enabling SecureBoot - HEFU.ROM should report exact size of .EFI image
- Typos in help content for profile VD for Write Policy
- HII cannot create a VD using unconfigured good drives as long as PD locate is set on the drives
- Obtain the Physical Slot number from the PCI Bridge to which the Controller is connected.

- Getting memory conflict during boot
- Memory access issue when loading Ctrl R
- OOB function corrupts EBDA area used by other server function
- not allocating memory correctly when MR and iMR are in the same system
- Optimize reading IO port in INT15h path
- System reboots during IO because FW didn't receive permanent host memory from OpROM
- OpROM is displaying incorrect value for the number of INT13h device it supports
- Provide an option to limit the max number of INT 13h devices presented to system BIOS
- Check the controller status bit in the function which hooks INT15
- Allocate only two 64k
- Add boundary checking when allocating EBDA and PMM memory for BIOS post.
- OpROM is displaying incorrect value for the number of INT13h device it supports
- Memory access issue for Mercury when loading Ctrl R
- Memory allocation: Allocate only two 64k
- OOB function corrupts EBDA area used by other server function
- Change Emergency Spare to NONE with enable emergency on Smarter checked will fail with error=03
- ctrl-r dosent list all the drives to do replace drive.
- Power savings button not enabled on Ctrl-R
- ctrl-H doesn't list the drives to do replace drive while doing copyback in PD MGmt Screen
- Selecting "Manage Link Speed" in CTL+R causes Fatal Error with SAS 9343-4i
- Implemented the safe mode in Ctrl-R
- Unable to make R10 through Ctrl R using 4k drives
- Default (Initial) setting of VD doesn't reflect MFC's setting
- /c0/pall show and Linkspeed information is not in same in Ctrl-R.
- Changes in BIOS mode (pause on error) to be in sync
- Need to display controller memory in Control-R
- showing "BIOS Mode" in both the pages of ctrl mgmt
- Help content is not updated with the Key stroke added
- VD Erase will be disabled in Ctrl+R when Initialization on particular VD
- Write policy is not added with writeback with BBu when MFC is set
- iMR boot Block code initial changes
- Errbios load fails on Fury adapters
- Merged 6.0 boot block changes to 6.1
- Bootblock is using NVRAM data even if NVRAM is uninitialized
- Configure chip reset to link down
- Added the code to enable OCM RMW errors
- Coherency bit is disabled in SRAM TLBs
- Numerous changes for specific customers
- PCLI(1.07.05) Sparc: Command "cli set securitykey=L
- Fcode CLI support for Invader (MR only)
- Define and use capability bit to identify the StorCLI

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Intel Drivers