Yamaha CL5 Digital Mixer Firmware 1.70 Download

Posted at November 25, 2024 by PCI-DB Team

Yamaha CL5 Digital Mixer Firmware 1.70 Description

New Features

- The Scene Memories, Libraries and Setup settings of a CL-series unit can now be saved/loaded individually from a USB flash drive.
- When switching input patches, you can now choose whether the HA settings of the patched ports continue to be used or the HA settings of the channels are copied to the ports.
- Sends from an input channel to a bus whose send point is set to PRE can now be assigned to be muted by a DCA group.
- Extra Metering points have been added to the METER screen.
- Functions have been added to the GAIN/PAN/ASSIGN knob (assignable encoder) when in SENDS ON FADER mode.
- In the GAIN/PATCH field of the SELECTED CHANNEL VIEW screen, the analog gain and digital gain of the head amp are both shown at all times.
- The HPF status of an external head amp such as the R-series is now shown in the GAIN/PATCH field of the SELECTED CHANNEL VIEW screen.
- Custom fader bank settings can now be stored/recalled individually for each scene.
- Black has been added as a channel color.
- The channel display now shows the channel on/off status in SENDS ON FADER mode.
- You can now select the attributes (latched or unlatched) of an external switch connected to a GPI IN port.
- It is now possible for Dante-related settings to be initialized when an error occurs on the Dante audio network.
- In the DCA/MUTE GROUP ASSIGN MODE popup window, you can now assign names to mute groups. In addition, the DCA group name and mute group name can be shown in this popup window.
- Aviom D800-Dante was added as a Dante device that can be detected and patched by the CL series.
- For details, refer to the CL Firmware V1.70 supplementary manual.

Improvements

- The limitations on a Dante DEVICE LABEL have been relaxed.
- The default value is panned hard LR rather than CENTER when PAN MODE is set to PAN for a ST IN on the CL console.
- If 15 or more channels are registered in the DCA member indication of the OVERVIEW screen, you can now use the multifunction knobs of the Centralogic section to scroll the channels.
- A link indicator has been added to the CH LINK MODE popup window, making it easier to determine the currently-assigned link group.
- The cue monitor level range has been expanded to -30 dB +20 dB.
- In the EFFECT popup window, GEQ popup window, and PREMIUM RACK popup window, you can now use the [SEL] keys to switch channels.
- If TAP TEMPO is assigned to a user defined key, and you specify the BPM (tempo value) by pressing that key, the BPM value is now shown in a popup window.

Fixed bugs

- Solved a problem in which GPI IN ACTIVE IND. did not function correctly.
- Solved a problem in which the Balance value of a Mix or Matrix bus was restricted when the Stereo/Mono setting of a bus was switched by RECALL SAFE, FOCUS RECALL, or GLOBAL PASTE, and then switched again.
- Solved a problem in which executing CH MOVE would cause an incorrect PAN value for the MATRIX of a ST IN.
- Solved a problem in which the Post On insert on/off setting of a STEREO bus was not always correctly applied to MATRIX SEND 2-8.
- Solved a problem in which the warning message "DANTE RESOURCE OVERFLOW" inappropriately appeared when a Dante device was powered-on or when the patch was changed significantly.
- Solved a problem in which the Dante latency of the CL/R series unit differed from the setting of the actual unit, and would not go below 1.0 ms.
- Solved a problem in which the SYSTEM indicator would not go dark when an error message shown in the Rio field of the I/O DEVICE screen (SYSTEM indicator blinking or lit) switched to a warning message (SYNC indicator blinking or lit).

Known issues

- If the Dante Virtual Soundcard (DVS) is patched to the CL series device using Dante Controller, the patching may not be recalled correctly when the CL series device is restarted. Patch DVS again. In addition, when using a version of DVS for Windows that is older than v3.2.0, the patch after CH41 cannot be performed from CL series consoles.
- If the setup of REDUNDANT/DAISY CHAIN is changed while the Dante device is not connected with Dante PRIMARY/SECONDARY connectors, no audio signal will pass. Audio will once again pass after the Dante device is connected of after the power for CL has been restarted.
- Loading of a file created by version V1.15 or older will not include the mount information of Dante devices other than any connected Rios. It is the same when recalling a DANTE INPUT PATCH LIBRARY. Please reset MOUNT, PATCH, and DANTE INPUT PATCH Library data using V1.51 if necessary.
- In some specific network switching conditions, a CL-series device may link at 100Mbps instead of the expected 1Gbps. This could be due to the self-checking function of some switches. Use the Device Status screen of Dante Controller to check the link speed of each device. If it shows up as 10 or 100, then disconnect the network cable for this device and re-connect it to correct the problem. To avoid the problem in most cases, first allow the network switches to fully boot up before turning the power on for the CL-series devices.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related YAMAHA Drivers