Buffalo WHR-300HP2 Router Firmware 1.80 Download

Posted at December 22, 2024 by PCI-DB Team

Buffalo WHR-300HP2 Router Firmware 1.80 Description

Changes:

- Fixed the issue where useless packets were sent to the wireless side when snooping functionality was enabled.
- Fixed the issue where useless multicast packets were translated to unicasts.
- Fixed the issue where IPv6 passthrough was not enabled even if it was enabled on the "Wireless Multicast Rate" page.
- Fixed the issue where on the "Routing" page, certain unusable destination addresses were usable, and certain usable destination addresses were unusable.
- Fixed the issue where settings could be restored even if the AirStation's firmware version was older than the firmware version used to create the config file.
- Fixed the issue where the error message for the encryption key was displayed on the "Easy Admin" page even if it is not needed.
- Fixed the incorrect text of the message displayed when eco mode was configured.
- Fixed the issue where the wireless bridge could not connect to the master router that did not broadcast SSIDs.
- Fixed the issue where in some situations, such as a power outage, settings were initialized or the AirStation and modem were shut down at the same time.
- Fixed the issue where if automatic update was enabled while the Ai
rStation was not connected to the Internet, the firmware version is displayed as the latest.
- Fixed the issue where the forwarded ports sometimes could not be edited correctly.
- Fixed the issue where communication via LAN-side to another gateway sometimes could not be established properly.- Fixed the issue where connected devices could not be displayed on the "Connected Clients List" page when 2.4 GHz wireless was disabled.
- Fixed the issue where the authentication screen was not displayed and the AirStation could not connect to the Internet when using some ISPs that require web authentication.
- Fixed the issue where an IP address could not be obtained when using some cable TV providers' Internet services.
- Fixed the issue where the AirStation kept its IP address after obtaining an IP address from the DHCP server even if the IP address was released when the AirStation was in access point mode.
- Fixed the issue where a ping test could not executed properly when the destination address was specified as a domain name.
- Fixed the issue where Settings could be accessed via the SSID whose SSID isolation was enabled.
- Fixed the issue where a config file saved while the AirStation was in router mode can restore settings when the AirStation is in access point mode.
- Fixed the issue where a config file saved while the AirStation was in access point mode can restore settings when the AirStation is in router mode.
- Fixed the issue where the DNS name resolution could not be done temporarily.
- Fixed the issue where the Internet-side multicast packets sometimes flowed into the LAN side.
- Fixed the issue where the AirStation could not connect to the Internet in access point mode when the AirStation connected to an SSID whose SSID isolation was enabled.
- Fixed the issue where the AirStation could not connect to the Internet in wireless bridge mode when the AirStation connected to the SSID whose SSID isolation was enabled.

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Buffalo Drivers