Panasonic AU-VREC1G Recording Module Firmware 7.50-00-0.00 Download

Posted at November 24, 2024 by PCI-DB Team

Panasonic AU-VREC1G Recording Module Firmware 7.50-00-0.00 Description

Changes:

- The lower limit of FPS setting range is extended. When HIGH SPEED is ON, FPS can be set from 1. FPS Setting Range: So far 120-240p / 100-200p / 60-120p / 50-100p → Changed to 1 - 240p / 1 - 200p / 1- 120p / 1 - 100p
- REC CHECK function is added. Playback function of the first or last 5-second footage of the last clip recorded after the power is turned on This is used after it is assigned to a User SW. The following items are added for assignment to USER1 – 4 in MENU.
- DESQUEEZE in playback is supported. Firmware is changed so that not only EE output but also a played clip is shown using DESQUEEZE when MENU -> ANAMORPHIC DESQUEEZE -> DESQUEEZE is ON. Varicam HS does not support ANAMORPHIC DESQUEEZE even in EE mode. VariCam 35 does not support DESQUEEZE in SUB-playback.
- CPS function is disabled. The CPS MENUs are disabled so that the setting, change, etc. of passwords are not allowed. However, if a CPS-encrypted medium is inserted into the camera, these MENUs are shown.
- Default setting for monitor output indication of USER CLIP NAME is changed to OFF. OUTPUT SETTINGS Menu MON OUT INDICATOR ->USER CLIP NAME（TYPE3) ->USER CLIP NAME :OFF
- Support for Add/Delete function of SHUTTER and WB via ROP App Supported App: VARICAM ROP Ver. 1.0.3 or later
- Support for connection for network via the access point (Infra mode).
- Supported wireless LAN modules are added. AJ-WM50MC (China) Automatic Channel Switching and GW-900D (PLANEX, Japan)
- Improvement: The indicator for remaining card capacity is corrected because it has a problem when the format is Long GOP on 23.98p of Frequency .

Upgrade Instructions:

- Download the firmware from the website.
- Insert an SD memory card into the SD card slot ( NOT microP2 card slot ) on the unit.
- Format the SD card (MENU: SYSTEM SETTINGS > CARDS/MEDIA > FORMAT CARD > SD CARD)
- Extract the ZIP package (you will see "PRIVATE" folder).
- Mount the formatted SD card to the computer then copy the "PRIVATE" folder to the SD card.
- Insert the SD card into the SD card slot (NOT microP2 card slot) on the unit.
- Disconnect the cable between the viewfinder and the camera body.
- Press INFO button to display INFO screen. Press the operation button of VERSION and press the Jog Dial..
- When “UPDATE” menu item appears, press the operation button of UPDATE > OK
- Wait until the “Version update successful” dialog is displayed. It may take approximately 60 minutes (Maximum).
- Remove the SD card.
- Switch OFF the power, and disconnect and connect DC power > switch ON the power to complete.
- Make sure the firmware version.

NOTE:

- The time required for update is approximately 60 minutes. It is necessary to supply power without interruption during the update. Use the external DC power supply instead of battery.
- Do not remove the SD memory card during the update (while the card access LED is flashing). The communication with the camera may be discontinued, which may cause malfunction to the camera.
- Disconnect the connection cable of the viewfinder when updating the camera module and the recording module.

Be sure to perform INITIAL ABB after the update.:

- This is for the sensor adjustment needed. The reference Black will be determined by this INITIAL ABB.
- Performing INITIAL ABB is not limited to immediately after the update. It can be redone many times, but please note that it should not be performed if the requirements below are not met.

MENU: SYSTEM SETTINGS > SYSTEM MODE:
- FREQUENCY: 59.94p
- PIXCEL: 4096 x 2160
- MAIN CODEC: AVC-Intra4K-LT
- HIGH SPEED: ON (60-120fps)

- Reboot the camera and wait for 15 minutes or longer with the power on.
- Check SENSOR TEMP and, if it is not between 38°C and 43°C, wait for a further 15 minutes or so.
- MENU: SYSTEM SETTINGS > INFORMATION > SENSOR TEMP between 38°C and 43°C (Temperature readings can be updated by pushing the jog dial button two times.)
- Be sure to put the lens cap or mount cap to block out the light completely.

Continue with:
- MENU: SYSTEM SETTINGS > COLOR SETTING
- MAIN V-709
- MENU: CAMERA SETTINGS > Enhanced > Enhanced SW > ON
- MENU: CAMERA SETTINGS > BLACK > INITIAL ABB (HIGH SPEED)
- DEFAULT BLACK BALANCE DATA OVERWRITTEN! Shade incoming light with lens cap before execute. - Confirm sensor temp.range:109F/43C to 100F/38C
- [EXECUTE] After about a minute, “ABB ACTIVE” is displayed on the panel.
 - When “ABB OK” is displayed, ABB is completed..

About Video Recorder Adapter Updates:

Applying a new firmware package on your Video Recorder adapter should improve overall performance and stability, fix various issues encountered with the device, or add support for newly developed features.

The Video Recorder adapter should be carefully upgraded by a power user (that is to say, someone who has the know-how to successfully complete the process), but it can also be performed by an average user at his or her own risk.

Either way, given the fact that each producer has their own method for installing a new firmware, and that every device has a particular way to enter the update mode, you must not consider upgrading the adapter's software until you have read and thoroughly understood the installation steps.

As a rule, said steps shouldn't pose too much of a challenge because manufacturers strive to make them as easy as possible. As with everything else, exceptions do occur, and users should be prepared for them.

Usually, you should transfer the compatible firmware to the Recorder through a USB cable or a memory card, and afterwards enter update mode from the unit's setup menu or through a specific power-on method.

With this in mind, if you intend to apply this release, make sure the package is compatible with your Video Recorder and that it brings about the changes you want or require; hit the download button and apply the new firmware.

Don't forget to regularly check with our website so that you don't miss any updates.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Panasonic Drivers