D-Link DSR-150 rev.A1 Router Firmware 1.09B32.ZIP Download

Posted at December 31, 2024 by PCI-DB Team

D-Link DSR-150 rev.A1 Router Firmware 1.09B32.ZIP Description

New Features:

Features added for both DSR-150 and DSR-150N:

1. L2TP client mode enhancements: support MPPE and demand dialing.
2. User DB enhancements: support PPTP/L2TP tunnels external authentication though AD, LDAP and POP3.
3. PPTP VPN enhancements: allow PPTP severs to assign remote clients the same subnet as the local LAN.
4. Russia Dual Access enhancements: allow users to designate the outbound interface for IGMP control packets.
5. Web GUI enhancements: support auto parameters fill-out in the DHCP server configuration page.
6. CLI enhancements: support the “space” character.
7. More 3G dongle supports: add D-Link DWM-156 A7, D-Link DWM-157 B1, and D-Link DWM-158 D1, HUAWEI E303. 8. A new click button to quickly download Dbglogs.
9. A new checkbox to enable/disable auto config backup.
10. A new checkbox to enable/disable config file encryption.
11. Support a Windows-based config viewer for encrypted config files.

Features added for DSR-150N only (DSR-150 had supported those features since 1.08B29)
1. Support L2TP VPN client mode.
2. Support 5 concurrent GRE tunnels.
3. Lengthen IPSec Pre-shared key length to 64 characters.
4. Simplify IGMP settings – allow all net to pass through DSR by default.
5. Add package manager with single selectable 3G driver support.

Problems

Fixed:
1. When WAN is configured using PPPoE, users can’t download files from FTP servers using passive mode.
2. When DSR-150(N) acts as an Open VPN server, Open VPN clients are allowed to authenticate themselves using certificates plus the username and password.

Firmware Update Steps

Do NOT upgrade firmware on any D-Link product over a wireless connection. Failure of the device may result. Use only hard-wired LAN network connections.

1. Save the current routers configuration to file. Tools/System. (Note that reloading this onto new major version of firmware can cause problems and thus is recommended to configure the router from scratch. Do not load the old configuration file from the old major version. If you're upgrading from minor to minor version, reloading of the configuration file shouldn't cause a problem. In these cases, please do not upload the previous older configuration file, rather set up the router from scratch. Should you need the configuration information from the previous saved configuration file, capture, copy or write down all required information from the configuration file loaded on the router BEFORE applying the newer firmware update.)

NOTE:

For routers using the new web page UI:
Management -> System Admin -> System
Save Settings To Local Hard Drive

2. Factory reset the router using the routers web page Tools/System, is easiest, or the back button.

3. Update the router using the routers web page Tools/System using the .bin file(s) that was downloaded for your product model. The .bin files have to be unpacked from the .zip file.

4. After the router as updated and status has reported it was successful on the routers web page, power OFF the ISP modem/ONT for 30 seconds then power back ON the modem/ONT. Perform one more Factory reset of the router using the routers web page Tools/System.

5. After the router has reset and come back to ready, reload the saved configuration file or reconfigure the router from scratch and walk thru the set up wizard. Status LEDs should be Blue, Green or White for power and internet (Globe) the router unit depending on model.

NOTE:

Clear all browser caches before and after loading FW files. 

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related D-Link Drivers