D-Link DWC-2000 rev.A1 Wireless Controller Firmware 4.3.0.3 Download

Posted at November 21, 2024 by PCI-DB Team

D-Link DWC-2000 rev.A1 Wireless Controller Firmware 4.3.0.3 Description

Problems Fixed:

1. [DBG14060159] The function of select-All is not work as expectation.
2. [DBG14060160] Channel bandwidth selection, Basic rate, support rate, auto eligible channel not work ( use case woks only issue with the GUI - low priority for now )
3. [DBG14070263] Critical error pop up on peer managed page under cluster topology.
4. [DBG14070261] Peer controller pager showed incorrect device number on WEB GUI under cluster topology.
5. [DBG14070078] The device shall refuse user to import over-spec number of license.
6. [DBG14070166] NB can't get IP address after change VLAN interface
7. [DBG14070085] With default built-in license, DUT cannot create over 64 APs entries in valid AP database
8. [DBG14070089] The DHCP server available lease time is different between LAN-settings and VLAN-settings
9. [DBG14070109] The RA feature shall not be able to disable while the DHCPv6 stateless mode is enabled.
10. [DBG14070093] DNS host name mapping shall automatically transfer the uppercase character. (works as per RFC but we DSR behavior was requested ).
11. [DBG14070107] The feature of "Radius Use Network" is not available on DWC-2000, thus it will cause problem if we turn the feature "on", need to remove this item from the menu
12. [DBG14070083] The feature of Session timeout is not work.
13. [DBG14060564] DWC-2000 doesn't send Radius-request message to radius server while running the WPA2-enterprise on 2.4Ghz radio, note that, 5Ghz radio is work without problem
14. [DBG14060167] The incorrect behavior as setup radio "Mode" ( use case woks only issue with the GUI - low priority for now )
15. [DBG14070260] Discover AP pager has pop up critical error under cluster topology
16. [DBG14070102] The managed APs location information will be incorrectly overwritten.
17. Sync DWS-4026 Auto Channel Algorithm Patch at 5GHz Issue (DI20140507000005) (The same patch in DWC-1000/v4302, SPR #44243)

Wireless Controller Firmware Upgrade

Path: Maintenance > Firmware > Firmware Upgrade > Using System (PC)

1. In the wireless controller web management interface, click Maintenance > Firmware > Firmware Upgrade.
2. If the firmware version on the D-Link support website has a higher number than the firmware version shown under Firmware Information, continue with this procedure.
3. Download the new firmware from the D-Link website.
4. Under Firmware Upgrade, click the Choose File button.
5. In the Choose File dialog box, navigate to the firmware file, and then click the file and click Open. If you want to upgrade using a file from a USB drive, click the Using USB tab near the top of this page.
6. Click Upgrade.
7. At the confirmation message, click OK to start the firmware upgrade. A progress bar shows the progress of the upgrade.
Note: The upgrade process takes a few minutes. Do not interrupt the upgrade or turn off the system; otherwise, you can damage the firmware. Wait for the upgrade to complete before browsing any sites from your browser.
8. When the upgrade completes, log in to the wireless controller web management interface, click Maintenance > Firmware > Firmware Upgrade, and confirm that the new firmware appears next to Firmware on the Using System (PC) page.
9. Record the firmware level in Appendix A.

About Device Firmware:

Applying a newer firmware version than the one already installed on your unit can bring various enhancements, include workarounds for diverse problems encountered by the device, and improve or add newly developed features.

On the other hand, downgrading the firmware version can recover the device’s functionality in the event of a software update either turning up faulty or causing the unit’s overall performance to drop. However, bear in mind that applying an older firmware isn’t recommended and might not always be possible.

When it comes to the update steps, due to the large variety of devices and numerous ways for installing a new firmware, it is recommended that you carefully read and understand the upgrade steps, and consider applying a different firmware only when you have familiarized yourself with the update method.

As the installation process is most of the times quite risky, this step should be taken by users that have the ability to successfully complete the update; regular users may initiate it at their own risk. Moreover, it’s best that this task be performed in a steady power environment such as the one ensured by a UPS unit.

Therefore, if you consider applying this release, hit the download button, take into account all the aforementioned aspects, and update the device’s firmware. Also make sure you constantly check with our website to ensure that you don’t miss a single new release.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related D-Link Drivers