D-Link DAP-3520 rev.A1 Access Point Firmware 1.15rc039 Download

Posted at December 23, 2024 by PCI-DB Team

D-Link DAP-3520 rev.A1 Access Point Firmware 1.15rc039 Description

New Features:

1. Support AP Array Setup Utility
2. Upgrade Wireless driver to version 7.3.0.449
3. Support “ping control” function
4. Add DNS setting on LAN Setting web page
5. Add HT20/40 coexistence enable/disable

Fixes:

1. Fix the error for ACL file upload in D-View and APM2
2. Fix the error info in the console log when running WDS endurance
3. Fix the when select year then day cannot be select in Time and Date
4. Correct the EG country code range
5. Fix when enable wireless schedule and vlan function the AP cannot be manage
6. Fix ”get multicastrate” always display 11Mbps in CLI
7. Fix ping through fail when MAC clone enabled for APC mode
8. Fix fail to manage AP caused by MAC confusion
9. Fix memory leak caused by SNMP module,
10. Fix bug when country as Israel, 5Ghz can be work
11. Fix when the current time is out of the range of the time, station still can associate to AP
12. Fix when AP Array Master AP leave and come back the role of Master AP issue
13. Fix when enable AP Array, the Limit Administrator IP range still worked
14. Fix application (indoor/outdoor) function bug when country code is JP in WEB and CLI and MIB
15. Fix set community didn't take effect when using CLI SNMP set host command
16. Fixe web page SNMP trap version bug.
17. Fixe ping delay issue when Ethernet port link down
18. Fixe memory leak issue caused by SNMP
19. Fixe that the WEB can’t disable VLan setup for Ethernet port when enable limit admin VLan id and save-active
20. Fix abnormal UI display in 5GHz and wireless setting cannot be saved anymore after pressing Scan button to site survey as 5GHz wireless client
21. Fix that DHCP discover packets without tagged after save and active
22. Fix APMII update config fail
23. Fix ath0 mode setting, the invalid parameter value will be set as ath0 mode
24. Fix the bug that the device reset to factory default when update configuration file using APMII or D-View
25. Fix the bug about auto channel selection function for 2.4GHz
26. Fix the bug that No WDS/WDS with AP selections when wireless band as 2.4GHz
27. Fix 11n client disconnect issue when transfer big size file(WEP+AES)
28. Fix ifTable ifindex for Multi-SSID
29. Fix the scheduling bug when F/W upgrade from v103 to v115
30. Fix the wrong IP address table in AP Array UI

Installation Procedure:

- Save the downloadable package.
- Log into the router’s web user interface.
- Navigate to the firmware upgrade section of your wireless unit.
- Select the present firmware and configure your router to install this file.
- Wait as the device carries out this process.
- Reboot the unit if required.

About Access Point Firmware:

If you update the Access Point (AP) firmware, your device can benefit from changes that fix multiple issues encountered by wireless clients, correct different user interface problems, add various functionalities, and include support for newly developed protocols.

Before performing this task, we recommend that you read and understand all the installation steps, because there are many AP models and manufacturers available. Each producer strives to make the procedure as simple as possible, but there are cases when it’s anything but that.

It is also advisable that you apply a new access point firmware in a steady power environment (UPS unit will satisfy this need), using an Ethernet cable rather than a wireless connection. The latter can be easily interrupted.

With this in mind, if you wish to apply this version, click the download button and install the package on your access point. Remember to check back with our website as often as possible so that you don’t miss a single new release.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related D-Link Drivers