Gigabyte GA-870A-UD3 (rev. 2.0) Realtek LAN Driver 6.250.0908.2011 for Vista Download

Posted at November 21, 2024 by PCI-DB Team

Gigabyte GA-870A-UD3 (rev. 2.0) Realtek LAN Driver 6.250.0908.2011 for Vista Description

Specifications:

CPU:
- Support for Socket AM3 processors: AMD Phenom II processor / AMD Athlon II processor

Hyper Transport Bus:

- 5200 MT/s

Chipset:

- North Bridge: AMD 870
- South Bridge: AMD SB850

Memory:

- 4 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory
- Dual channel memory architecture
- Support for DDR3 1866(OC)/1333/1066 MHz memory modules

Audio:

- Realtek ALC892 codec
- High Definition Audio
- 2/4/5.1/7.1-channel
- Support for Dolby Home Theater
- Support for S/PDIF In/Out
- Support for CD In

LAN:

- 1 x Realtek 8111D chip (10/100/1000 Mbit)

Expansion Slots:

- 1 x PCI Express x16 slot, running at x16 (PCIEX16)
- 1 x PCI Express x16 slot, running at x4 (PCIEX4)
- 2 x PCI Express x1 slots (The PCIEX1_1 and PCIEX1_2 slots share bandwidth with the PCIEX4 slot.)
- 3 x PCI slots

Storage Interface:

- 6 x SATA 6Gb/s connectors supporting up to 6 SATA 6Gb/s devices
- Support for SATA RAID 0, RAID 1, RAID5, RAID 10, and JBOD
- SATA3 RAID 0 4x and SATA3 2x performance are maximum theoretical values. Actual performance may vary by system configuration.

GIGABYTE SATA2 chip:

- 1 x IDE connector supporting ATA-133/100/66/33 and up to 2 IDE devices
- 2 x SATA 3Gb/s connectors supporting up to 2 SATA 3Gb/s devices
- Support for SATA RAID 0 and RAID 1 and JBOD

JMicron JMB362 chip:

- 2 x eSATA 3Gb/s connectors on the back panel supporting up to 2 SATA 3Gb/s devices
- Support for SATA RAID 0, RAID 1, and JBOD

iTE IT8720 chip:

- 1 x floppy disk drive connector supporting up to 1 floppy disk drive

USB:

- Up to 12 USB 2.0/1.1 ports (8 on the back panel, 4 via the USB brackets connected to the internal USB headers)
- NEC chip: Up to 2 USB 3.0/2.0 ports on the back panel

IEEE 1394:

- T.I. TSB43AB23 chip: Up to 3 IEEE 1394a ports (2 on the back panel, 1 via the IEEE 1394a bracket connected to the internal IEEE 1394a header)

Internal I/O Connectors:

- 1 x 24-pin ATX main power connector
- 1 x 8-pin ATX 12V power connector
- 1 x floppy disk drive connector
- 1 x IDE connector
- 6 x SATA 6Gb/s connectors
- 2 x SATA 3Gb/s connectors
- 1 x CPU fan header
- 2 x system fan header
- 1 x power fan header
- 1 x front panel header
- 1 x front panel audio header
- 1 x CD In connector
- 1 x S/PDIF In header
- 1 x S/PDIF Out header
- 1 x IEEE 1394a header
- 2 x USB 2.0/1.1 headers
- 1 x serial port header
- 1 x parallel port header
- 1 x clearing CMOS jumper

Back Panel Connectors:

- 1 x PS/2 keyboard or mouse port
- 1 x optical S/PDIF Out connector
- 1 x coaxial S/PDIF out connector
- 8 x USB 2.0/1.1 ports
- 2 x USB 3.0/2.0 ports
- 2 x IEEE 1394a port
- 2 x eSATA 3Gb/s ports
- 1 x RJ-45 port
- 6 x audio jacks (Center/Subwoofer Speaker Out/Rear Speaker Out/Side Speaker Out/Line In/Line Out/Microphone)

I/O Controller:

- ITE IT8720 chip

H/W Monitoring:

- System voltage detection
- CPU/System temperature detection
- CPU/System/Power fan speed detection
- CPU overheating warning
- CPU/System/Power fan fail warning
- CPU/System fan speed control

Form Factor:

- ATX Form Factor: 30.5cm x 23.0 cm

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related REALTEK Drivers