Panasonic AU-VREC1G Recording Module Firmware 8.00-00-0.02 Download

Posted at December 22, 2024 by PCI-DB Team

Panasonic AU-VREC1G Recording Module Firmware 8.00-00-0.02 Description

Fixes:

- [35 | HS] CSS(Custom Splash Screen): The display screen during the boot-up process (Splash Screen) can be customized to show a company’s logo, etc. This software helps deter theft by using the customized Splash Screen as the owner's digital name tag. Customize the Splash Screen as your company logo, Register owner information, Password setting. You can set a password to prevent rewriting of the above registered contents and to prevent updating / downgrade execution.
- [35 | HS] The time required for displaying GUI at boot-up is reduced.
- [35 | HS] The size of the REC mark on OSD is increased.
- [35 ] SYSTEM MODE can be changed by selecting the preset item.
- [35 ] ISO BASE ([800B] / [5000B]) is displayed. (VF, MON OUT, LCD (VIEW))
- [35 | HS] RESTART function is added to the control panel. RESTART button is added so that the camera can be rebooted by means of the control panel, instead of the power switch, after the system mode is changed. RESTART button is added so that the camera can be rebooted, after NETWORK SEL is changed.
- [35 ] For the following settings where VFR is possible, VFR ON/OFF Switching feature is provided. REC FORMAT: LT codec and PIXEL: CROP mode
- [35 | HS] Icons are added for indicating FF/REW playback. The 16x high-speed playback function is added.
- [35 | HS] The following compatible wireless LAN module is added. D-Link DWA171 (Australia)

Upgrade Instructions:

- Download the firmware from the website.
- Insert an SD memory card into the SD card slot ( NOT microP2 card slot ) on the unit.
- Format the SD card (MENU: SYSTEM SETTINGS > CARDS/MEDIA > FORMAT CARD > SD CARD)
- Extract the ZIP package (you will see "PRIVATE" folder).
- Mount the formatted SD card to the computer then copy the "PRIVATE" folder to the SD card.
- Insert the SD card into the SD card slot (NOT microP2 card slot) on the unit.
- Disconnect the cable between the viewfinder and the camera body.
- Press INFO button to display INFO screen. Press the operation button of VERSION and press the Jog Dial..
- When “UPDATE” menu item appears, press the operation button of UPDATE > OK
- Wait until the “Version update successful” dialog is displayed. It may take approximately 60 minutes (Maximum).
- Remove the SD card.
- Switch OFF the power, and disconnect and connect DC power > switch ON the power to complete.
- Make sure the firmware version.

NOTE:

- The time required for update is approximately 60 minutes. It is necessary to supply power without interruption during the update. Use the external DC power supply instead of battery.
- Do not remove the SD memory card during the update (while the card access LED is flashing). The communication with the camera may be discontinued, which may cause malfunction to the camera.
- Disconnect the connection cable of the viewfinder when updating the camera module and the recording module.

Be sure to perform INITIAL ABB after the update.:

- This is for the sensor adjustment needed. The reference Black will be determined by this INITIAL ABB.
- Performing INITIAL ABB is not limited to immediately after the update. It can be redone many times, but please note that it should not be performed if the requirements below are not met.

MENU: SYSTEM SETTINGS > SYSTEM MODE:
- FREQUENCY: 59.94p
- PIXCEL: 4096 x 2160
- MAIN CODEC: AVC-Intra4K-LT
- HIGH SPEED: ON (60-120fps)

- Reboot the camera and wait for 15 minutes or longer with the power on.
- Check SENSOR TEMP and, if it is not between 38°C and 43°C, wait for a further 15 minutes or so.
- MENU: SYSTEM SETTINGS > INFORMATION > SENSOR TEMP between 38°C and 43°C (Temperature readings can be updated by pushing the jog dial button two times.)
- Be sure to put the lens cap or mount cap to block out the light completely.

Continue with:
- MENU: SYSTEM SETTINGS > COLOR SETTING
- MAIN V-709
- MENU: CAMERA SETTINGS > Enhanced > Enhanced SW > ON
- MENU: CAMERA SETTINGS > BLACK > INITIAL ABB (HIGH SPEED)
- DEFAULT BLACK BALANCE DATA OVERWRITTEN! Shade incoming light with lens cap before execute. - Confirm sensor temp.range:109F/43C to 100F/38C
- [EXECUTE] After about a minute, “ABB ACTIVE” is displayed on the panel.
- When “ABB OK” is displayed, ABB is completed.. 

About Video Recorder Adapter Updates:

Applying a new firmware package on your Video Recorder adapter should improve overall performance and stability, fix various issues encountered with the device, or add support for newly developed features.

The Video Recorder adapter should be carefully upgraded by a power user (that is to say, someone who has the know-how to successfully complete the process), but it can also be performed by an average user at his or her own risk.

Either way, given the fact that each producer has their own method for installing a new firmware, and that every device has a particular way to enter the update mode, you must not consider upgrading the adapter's software until you have read and thoroughly understood the installation steps.

As a rule, said steps shouldn't pose too much of a challenge because manufacturers strive to make them as easy as possible. As with everything else, exceptions do occur, and users should be prepared for them.

Usually, you should transfer the compatible firmware to the Recorder through a USB cable or a memory card, and afterwards enter update mode from the unit's setup menu or through a specific power-on method.

With this in mind, if you intend to apply this release, make sure the package is compatible with your Video Recorder and that it brings about the changes you want or require; hit the download button and apply the new firmware.

Don't forget to regularly check with our website so that you don't miss any updates.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Panasonic Drivers