PCI-DB.com
  1. Driver
  2. Router Switch Access Point
  3. Xwrt-Vortex Firmware 380.59.0 for Netgear R7000

Xwrt-Vortex Firmware 380.59.0 for Netgear R7000 Download

Posted at December 24, 2024 by PCI-DB Team

Install Driver Automatically
Device NameXwrt-Vortex Firmware 380.59.0 for Netgear R7000
CategoryRouter Switch Access Point
ManufacturerNETGEAR
File Size53.8 MB
Supported OSOS Independent

Xwrt-Vortex Firmware 380.59.0 for Netgear R7000 Description

Xwrt-Vortex is a port of Asuswrt-Merlin for different routers developed by Vortex. Xwrt-Vortex retains all the features of the original stock Asus firmware.

Installation:

Simply flash it like any regular update. You should not need to reset to factory defaults. You can revert back to an original Asus firmware at any time just by flashing a firmware downloaded from Asus's website.

NOTE:

resetting to factory default after flashing is strongly recommended for the following cases:
- Updating from a firmware version that is more than 3 releases older
- Switching from a Tomato/DD-WRT/OpenWRT firmware

If upgrading from anything older and you experience issues, then consider doing a factory default reset then as well. Always read the changelog, as mandatory resets will be mentioned there when they are necessary.

In all of these cases, do NOT load a saved copy of your settings! This would be the same thing as NOT resetting at all, as you will simply re-enter any invalid setting you wanted to get rid of. Make sure to create a new backup of your settings after reconfiguring.

Changes:

- CHANGED: SSH WAN access will also work over IPv6
- CHANGED: Updated miniupnpd to 2.0
- CHANGED: Fields on the DHCP static lease page are now sortable (original patch by Allan Jensen)

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related NETGEAR Drivers

NETGEAR WNA1100 WiFi Adapter Firmware 2.2.0.1

Device Type: Network Card File Size: 24.9 MB Windows XP ,Windows Vista ,Windows XP 64 bit ,Windows Vista 64 bit ,Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows 8.1 ,Windows 8.1

Install Driver

Netgear MP101 Firmware 1.3.5

Device Type: Firmware File Size: 18.9 MB Windows 9X ,Windows ME ,Windows NT ,Windows 2K ,Windows XP ,Windows 2003 ,Windows Vista ,Windows XP 64 bit ,Windows 2008 ,Windows Vista 64 bit ,Window

Install Driver

Netgear DGFV338 Firmware 302-20

Device Type: Firmware File Size: 7.4 MB Windows 9X ,Windows ME ,Windows NT ,Windows 2K ,Windows XP ,Windows 2003 ,Windows Vista ,Windows XP 64 bit ,Windows 2008 ,Windows Vista 64 bit ,Window

Install Driver

Netgear WG511v2 Driver 3.1

Device Type: Network Card File Size: 20.2 MB Windows 9X ,Windows ME ,Windows NT ,Windows 2K ,Windows XP ,Windows 2003 ,Windows Vista ,Windows XP 64 bit ,Windows 2008 ,Windows Vista 64 bit ,Window

Install Driver

Find Missing Drivers

© 2024 PCI-DB.com - PCI Database Replacement. All rights reserved.