NETGEAR WNR2000v2 Router Firmware 1.0.0.40 (WW) Download

Posted at December 23, 2024 by PCI-DB Team

NETGEAR WNR2000v2 Router Firmware 1.0.0.40 (WW) Description

Fixes:

- Change web GUI title to "N300 Wireless Router model WNR2000v2".
- Added Traffic Meter support for DHCP/BPA/Static IP.
- Remove WPA-PSK security mode from repeating function.
- Move Time Zone setup from "Email" page to "Schedule" page.
- Move "Enable SSID Broadcast" option and "Enable Wireless Isolation" option to "Basic" page.
- Add more pre-set service for the Block Service function.
- Cannot support 64 static routes through the DHCP option 33 and 121.
- Traffic Meter: Set limit to 50Mbps and it will stop at 47.02Mbps, the result is not accurate.
- Wireless LED turns off if disable the wireless and reboot it and then push the wireless on/off button to re-enable wireless.
- Traffic Meter "Start Date/Time" value will show the time thats present while clicking "Restart Counter Now" button.
- Basic setting page shows abnormally after detected BPA.
- Wireless ACL table will show blank if added device name contains “<”.
- Internet access becomes slow when connection table is full.
- Traffic Meter hijacking is still effective after restart counter.
- “Enable Traffic Meter” checkbox will be unchecked in IE6 after Restart Counter.
- Firmware checking/Uplink Bandwidth checking/Changing language can't trigger the Dial on Demand PPTP/BPA connection.
- Live Parental Control/Open DNS and Smart Wizard CD can’t work if UPNP is disabled.
- Power LED doesn’t flash while performing Internet firmware upgrade.
- The start page can't be shown on Safari 4.x.
- Router may crash while using Windows Live Messenger in a system with 3 or more interfaces.
- Smart Wizard can’t detect PPPoE with ATT modem.
- Router can't disconnect SIP session after calling an virtual client.
- Router can't deal with conflict UPnP port mapping service and port forwarding.
- There's no log entry about disconnected after PPTP disconnected.
- FTP port forwarding is inaccessible in FTP passive mode.
- Router can’t resolve QoS Device Name with blank characters.
- "QoS Priority Rule List" page will show 32 same QoS rules if user adds only one rule categorized by "MAC Address" after delete all default and then reboot.
- Router with Russian GUI can't trigger DoD PPTP connection at the second time when WAN set to static PPTP (My IP is set) with fixed DNS servers and PPTP server address is a domain name
- If there is a port triggering rule with a TCP port, then user can’t add an UDP port rule with the same port.
- WAN connection will be restarted if click "Restart Counter Now".
- Empty "Monthly limit" and "Round up volume" is not checking in Traffic Meter page.
- Fix a potential issue that UPnP agent may crash when receive a PIPE signal.
- Output printing message to standard error device while executing some MFG command to reduce testing time.
- Fix a potential endless loop issue while checking ppp0 interface.
- Fixed: base station address won’t be shown in router status page issue.
- Fix an issue that router will add some extra string in string table file while upgrading string table through web page.
- The start page can't be shown on Safari 4.x
- Internet PPPoE/PPTP idle time is not precise at the first time.
- Restarting WPS process will cause router to get out of temporary lock-down state.
- Guest Network PCs are allowed to ping Router if the option "Allow guest to access my local network" is not checked
- When enabled MAC address/LAN port QoS in PPPoE/PPTP mode, fragmented UDP packets may cause NAT crash
- Parental Control (OpenDNS) can't work if there is server failure response after query a domain name.
- Connection status window can’t be updated in PPPoE mode with IE6 some times.
- Remote management can't work with port 5000.
- Router needs reboot to take effect of configuration.
- Maximum value of Traffic Meter month limit can’t be set to 999GB (6 digits).
- "Download Traffic Volume" value will ascend the same as upload value.
- Multi-Language GUI issues about translation and format.
- Built-in string table is not updated to flash if upgrade a newer firmware with newer string table through NMRP. (TEC)

Note:

- Do not upgrade the firmware using a wireless connection. Please perform firmware upgrade with “wired” or Ethernet connection only.
- The upgrade process is completed when the on screen progress bar completes. If power LED light turns amber and blinking, power cycle the router to complete the upgrade.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related NETGEAR Drivers