Revolabs HDEXEMIC-11 HD Microphone Firmware 2.6.33 Download

Posted at December 18, 2024 by PCI-DB Team

Revolabs HDEXEMIC-11 HD Microphone Firmware 2.6.33 Description

How to Update HD Firmware:

1. Download our HD Firmware
2. Download HD Control Panel Software (Don’t Install the Software Yet!! This is done in a later step.) If you a previous version of the HD Control Panel installed already you should uninstall this version and use the latest version (click the download link above) instead. 
3. Place microphone charging base (with all microphones in the base) in proximity to your PC and plug in a USB to Mini-USB cable. The charger must also be plugged via its electrical power adaptor as well. Windows should detect the charger as an unknown USB Device, this is okay.
4. Install the Revolabs HD Software you downloaded in Step 2. This should properly install the Windows driver for the HD charger. A command prompt window (looks like a MS-DOS window) should pop up that says Installing Driver to confirm the driver is being installed.
5. Power Up your HD Executive Receiver if you have not done so already.
6. Direct connect a CAT5 Straight through cable from your PC’s Ethernet port to the LAN port on the back of your HD Executive Receiver.
7. Disable your wireless internet connection if you’re using one, the only connection should be between the HD Box and your laptop via the CAT5 cable.
8. Using the LCD Screen and Buttons on the front of your Executive HD, hit the home/house button, and then scroll down to DHCP. Press Enter to Turn DHCP off. Reboot the Executive HD using the power switch on the back of the unit.
Note: If DHCP is already off on this system and it already has an IP address, a static IP has already been set. You may skip this step and proceed to step 10.
9. Once the system boots up, it should pull a Windows based IP address. This may take up to 1 minute to occur.
10. Set the current IP in your laptop as static one Octet away from the Executive HD.
For instance if the HD Box is: 169.168.100.50 set your Laptop to 169.168.100.51
11. Open the HD Control Panel Software. It can be found on the Windows Start Menu, under Programs and then Revolabs.
12. Select System> Scan the Network
13. It should list your HD Executive here. Click the check box to select it and then click Okay.
14. Go to Firmware>update firmware - Make sure both the Base and Microphones checkboxes are checked.
15. Use the Choose button to locate and select the firmware file you previously downloaded. Select the .zip firmware file and click Open, and then Okay.
16. Firmware should begin updating for Receiver and Microphones, when the process is complete the Software will say “Base and Mic firmware update complete”. You may see the system reboot during the update process and temporarily lose its IP address, this is normal.
17. If you receive an FTP Error immediately upon starting the update process, you may need to disable Windows Firewall, close the software, reboot the HD box, and attempt the FW update again. If you continue to receive this error, please check your PC for other Internet Security software that could be inhibiting the HD Control Panel Software.

About Device Firmware:

Applying a newer firmware version than the one already installed on your unit can bring various enhancements, include workarounds for diverse problems encountered by the device, and improve or add newly developed features.

On the other hand, downgrading the firmware version can recover the device’s functionality in the event of a software update either turning up faulty or causing the unit’s overall performance to drop. However, bear in mind that applying an older firmware isn’t recommended and might not always be possible.

When it comes to the update steps, due to the large variety of devices and numerous ways for installing a new firmware, it is recommended that you carefully read and understand the upgrade steps, and consider applying a different firmware only when you have familiarized yourself with the update method.

As the installation process is most of the times quite risky, this step should be taken by users that have the ability to successfully complete the update; regular users may initiate it at their own risk. Moreover, it’s best that this task be performed in a steady power environment such as the one ensured by a UPS unit.

Therefore, if you consider applying this release, hit the download button, take into account all the aforementioned aspects, and update the device’s firmware. Also make sure you constantly check with our website to ensure that you don’t miss a single new release.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Revolabs Drivers