LILIN ZR6122E IP Camera Firmware 1.0.60 Download

Posted at December 18, 2024 by PCI-DB Team

LILIN ZR6122E IP Camera Firmware 1.0.60 Description

Fixes:

1.Supported the IE11 browser.
2.Fixed if the HTTP Port is not 80, the SD card webpage doesn't show the video when playback.
3.Modified the buttons of SD card playback webpage and the size of the screen when playback.
4.Added the feature if the watchdog reboots three time in a row, the video setting goes back to default.
5.If the SD card is in always record mode, the time interval between the recorded files get reduced.
6.Fixed when using the quicktime to play the UDP stream, there is no audio output.
7.Fixed the frame rate limited in ONVIF.
8.Added the Turkish language.
9.Fixed when connected with the NVR if the frame rate low which can get video loss easily.
10.Modified the default setting of video quality to +5 for night mode.
11.Modified the typesetting for tamper webpage.
12.Modified the operator rights. If an operator is created by administrator, the "Administrator" box is not checked and the "Panel Control" is checked so that the administrator can add this operator as admin right at any time.
13.Fixed when using the IPScan to change the IP address if the IPCam is connected by NVR or CMX, the H264 and JPEG get stuck by 1 online user.
14.Fixed the avi files of the SD card recording that the pre-recording and the current triggered recorded video files are both included the wrong video data.
15.Fixed if continuously click the video files to playback the files in SD card, it can cause the files not to be playback properly.
16.Fixed the SD card backup when the file is finished playing, it will not repeat playing.
17.When enable the "Bypass Logon" feature, the RTSP authentication will be disabled.
18.Fixed when the face detection is enabled but there is no log recorded.
19.Fixed when enable the "Bypass Logon", the webpage shows an message of updating error.
20.The baseline mode is removed and the only setting is main profile now.
21.Updated the ActiveX to 1.0.50.112 version which supports to show up the ActiveX recording time.

Update firmware from web interface

1. Login into the IP Camera via IE.
2. Click on Configure->System->Firmware Update
3. Click on "Browse" button to locate the firmware file, flasham32.bin.
4. Click on "OK" button.
5. Wait the web interface to be reloaded again.

WARNING!

YOU DO NOT HAVE TO UPGRADE THE LATEST FIRMWARE. HOWEVER, THE LATEST FIRMWARE CAN IMPROVE THE DEVICE's SYSTEM PERFORMANCE. THERE ARE ALSO RISKS FOR UPGRADING THE NEW FIRMWARE INCLUDING POWER FAILURE, LOW BANDWIDTH, or FLSAH DISK BROKEN.
THE RESULT MAY REQUIRE RETURNING the DVR BACK TO YOUR ORIGINAL PROVIDER FOR REPAIRING.

About Network Camera Firmware:

Updating to a newer firmware version than the one already installed on your network camera can improve the device’s overall performance and stability, resolve various issues, and add support for newly developed features or enhance existing ones.

On the other hand, downgrading the camera’s firmware can recover its functionality in the unlikely event the currently installed version is faulty, or the device’s performance dropped after an upgrade. However, bear in mind that applying an earlier build might not always be possible.

Changing the camera’s firmware must be performed when the new release resolves an issue that your device has encountered or adds a new feature (or enhances an existing one) that could prove useful to you.

As for the installation method, the steps vary depending on the model you own, but basically, you must connect your camera via an Ethernet cable (username and password required), and use the downloadable file in the Firmware Update section to upgrade your device. Make sure you do not interrupt the installation process.

However, make sure you carefully read and understand the installation steps so that you don’t end up with a broken device. This process isn’t intended to be destructive, but still, it’s best to save all configurations before applying a different firmware.

That being said, if you consider that this firmware improves your device in any way, then hit the download button and get the desired version; if not, check our website as often as possible so that you don’t miss the update that will boost your camera’s performance. 

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related LILIN Drivers