Ubiquiti EdgePoint EP-S16 Switch Firmware 1.7.4 Download

Posted at December 30, 2024 by PCI-DB Team

Ubiquiti EdgePoint EP-S16 Switch Firmware 1.7.4 Description

New features

- [Simple GUI] Added brand new simple web-interface design to provide a better experience using the Graphical User Interface (GUI). It provides an intuitive, faster way to configure and display the status of EdgeSwitches.
- [Client Info] Add new feature client information, this feature tries to collect the client information like MAC address, IP address(IPv4) and Hostname in EdgeSwitch.

Default config changes

- [HTTPS] Enable default HTTPS server with high priority.
- [SSH/TELNET] Enable SSH and disable default telnet server.

Bug fixes and enhancements

- [SYSTEM] adjust the display method for CPU utilization.
- [SYSTEM] fine tune SFP+ tx parameters in ES48/EP-S16.
- [SYSTEM][HTTP/HTTPS] fix hard timeout.
- [SYSTEM] add throughput statistics.
- [SYSTEM][Auto-Detect] optimize and fix issue when insert modules.
- [SYSTEM][ESGH] enable 2.5G and support Aquantia 2.5G SFP+/RJ-45 transceiver.
- [SYSTEM] fix process in auto-install.
- [CLI] update CLI banner.
- [CLI] allow specific characters in port description.
- [CLI] remove limititation of speed change on LAG ports.
- [CLI] fix secure-protocol running-config.
- [CLI] add hint advertise when enable auto-voip oui.
- [CLI] fix show issue in "show logging traplogs".
- [LAG] extend maximum LAG number to 32.
- [LAG] set LAG mode to dynamic (LACP) as default.
- [LAG] fix config and change WebUI and CLI.
- [PoE] add reminder when enabling passive PoE by WebUI/CLI.
- [PoE][PingWatchDog] fix some lock in some special case.
- [SECURITY] fix some security issues in WebUI.
- [SECURITY] fix some security issues in CLI.
- [DOT1X] fix some updating problem when MAC migrate.
- [IGMP] extern IGMP group membership interval to 65535.
- [ROUTING] extend L3 ARP table size (ESWH: 493, ESGH: 749).
- [UNMS] fix some file lock in UNMS configuration.
- [DHCPv6 Snooping] fix issues in parser.
- [IGMP Snooping] fix DHCPv6 problems with "igmp snooping" in MacOS.
- [MLD] Enable MLD snooping (CLI).
- [WEBUI] adjust for new UI.
- [DOT1X] Add NAS-IP Address attribute in radius packet.

About Switch Firmware:

Given the large variety of models and different methods for upgrading the switch, if you wish to apply this package, we recommend that you read and understand the installation steps before you install a new firmware, even if you are a power user.

Usually the update procedure isn't much of a hassle as manufacturers try to make it as simple as possible; however, there are cases that are exceptions to this rule. First off, go to the system information page of the switch to check that the currently installed version isn't either newer or matching this release.

Applying a new firmware can decrease the security vulnerabilities, enhance overall performance and compatibility, improve various power management functions, resolve different errors, and add support for newly developed technologies and protocols.

It is recommended that you perform this step in a steady power environment such as the one ensured by a UPS unit, and that you don't interrupt the upgrade in any way, because this might cause the switch to malfunction.

That being said, click the download button, get and apply the new version, and check back with our website constantly to stay up to speed with the latest releases.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Ubiquiti Drivers