Posted at December 23, 2024 by PCI-DB Team
Install Driver AutomaticallyDevice Name | Ubiquiti PBE-5AC-400 Bridge Firmware 8.0.32148.161216 |
---|---|
Category | Network Card |
Manufacturer | Ubiquiti |
File Size | 8.1 MB |
Supported OS | OS Independent |
- New: Compatibility with airMAX M stations (airOS v6.0 required)
- New: airOS8 WEB UI re-design/adoption for mobile
- New: airMagic: channel selection tool (available on Access Point mode only, not all AC models supports airView radio). Access Point and Stations must run airOS8 and have dedicated airView radio. It takes few minutes to gather data after upgrade/reboot.
- New: Added "TDMA Filter" slider. "TDMA Filter" allows the operator to specify how much the airMAX-ac scheduler should penalise poor performing clients from a scale of 0 to 9.
- New: MAC ACL support
- New: Automatic Power Control
- New: Hour Average & Minute Peak options in AirView (for better troubleshooting)
- New: Audio Indicator to Antenna Align tool
- New: Possibility to enable/disable Multicast enhancement feature
- New: Remote provisioning functionality with airGateway
- New: Indication of too high RX signal in Station List
- New: Indication of compatibility mode wlanOpmode in mca-status
- New: Indication of signal difference per chain when it exceeds recommended maximum of 5 dBm
- New: Enable Block management access on WAN when switching to Router mode
- New: Read-Only account support
- New: HTTP login success/failures logging to system log
- New: Crashlog reporting to Ubiquiti Networks for better troubleshooting
- New: Noise Floor reporting in Dashboard
- New: iptables modules allowing DSCP marking
- New: Sensitivity Threshold on Wireless page
- New: DHCP Reservation on Router mode
- New: Option allowing LLDP packets to pass wireless bridge
- New: Help file for Wireless Mode in Wireless Settings
- New: Help file for Audio Indicator in Antenna Align Tool
- New: miniUPnPd version update
- LiteBeam 5AC 23: Added activation of Revised UNII band
- 5GHz frequency list update for Italy: removed 5725-5875 MHz frequency range
- 5GHz frequency list update for Germany: removed 5735-5755 MHz range
- Removed 5.8 GHz band (EN 302 502) as not allowed for Czech Republic
- Removed North America and Puerto Rico from country list for WORLD version products manufactured after 01/01/2017. Previous production data products are not affected.
- Fix: Select WAN interface for Port Forward rule by default
- Fix: Optimise statistics collection (reduce CPU usage)
- Fix: TX/RX counter does not reset at 4GB
- Fix: Generate SSL certificate start date from firmware build timestamp
- Fix: Ethernet link drops when connected to specific switch models
- Fix: Don't check certificate start date if device date/time is before certificate start date (EAP TTLS/PEAP)
- Fix: Ethernet RX packets drop when Flow Control is enabled
- Fix: Increased Max MTU value to 2024 Bytes on WA products
- Fix: Do not load NAT helpers modules when NAT is disabled
- Fix: VOIP Group call doesn't work with 5 VOIP clients behind STA (Router)
- Fix: Memory usage optimisation
- Fix: RADIUS accounting stop frame on Client disconnect
- Fix: Lower MTU fragmentation fix
- Fix: DHCP on Multiple LAN interfaces separate DNS not working
- Fix: PPPoE blank password sending [email protected]
- Fix: Enable Flow Control on Ethernet (LAN) after reset to factory defaults only
- Fix: LAN port lockup on 10 Mbps-Half/10 Mbps-Full modes (WA series)
- Fix: AP doesnâ€t broadcast new Device Name after change. Reboot is required
- Fix: SSID length for SNMP increased up to 32 characters
- Fix: Device Name with not allowed symbols breaks DHCP
- Fix: Changed AP device name does not take effect until reboot
- Fix: airOS security improvements
- Fix: Stability fixes (random reboots, crashes)
- WEB UI: Keep NAT helper modules disabled when enabling NAT
- WEB UI: Automatically create BRIDGE interface for each new VLANs in AP-Router setup (due to the low performance when WLAN0.vlan_id isn't included in BRIDGE)
- WEB UI: Added Output Interface selection in Firewall Rules
- WEB UI: Check for uploaded firmware image on device
Applying a newer firmware version than the one already installed on your unit can bring various enhancements, include workarounds for diverse problems encountered by the device, and improve or add newly developed features.
On the other hand, downgrading the firmware version can recover the device’s functionality in the event of a software update either turning up faulty or causing the unit’s overall performance to drop. However, bear in mind that applying an older firmware isn’t recommended and might not always be possible.
When it comes to the update steps, due to the large variety of devices and numerous ways for installing a new firmware, it is recommended that you carefully read and understand the upgrade steps, and consider applying a different firmware only when you have familiarized yourself with the update method.
As the installation process is most of the times quite risky, this step should be taken by users that have the ability to successfully complete the update; regular users may initiate it at their own risk. Moreover, it’s best that this task be performed in a steady power environment such as the one ensured by a UPS unit.
Therefore, if you consider applying this release, hit the download button, take into account all the aforementioned aspects, and update the device’s firmware. Also make sure you constantly check with our website to ensure that you don’t miss a single new release.
It is highly recommended to always use the most recent driver version available.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.
Device Type: Network Card File Size: 8.1 MB OS Independent
Install DriverDevice Type: Network Card File Size: 8.1 MB OS Independent
Install DriverDevice Type: Network Card File Size: 8.1 MB OS Independent
Install DriverDevice Type: Network Card File Size: 8.1 MB OS Independent
Install DriverDevice Type: Network Card File Size: 7 MB OS Independent
Install DriverDevice Type: Network Card File Size: 8.1 MB OS Independent
Install DriverDevice Type: Network Card File Size: 8.1 MB OS Independent
Install DriverDevice Type: Network Card File Size: 7 MB OS Independent
Install DriverDevice Type: Network Card File Size: 8.1 MB OS Independent
Install DriverDevice Type: Network Card File Size: 7 MB OS Independent
Install DriverFind Missing Drivers
Recent Devices
Recent Drivers
© 2024 PCI-DB.com - PCI Database Replacement. All rights reserved.