Ubiquiti M2 Antenna Firmware 5.6.3 Download

Posted at December 26, 2024 by PCI-DB Team

Ubiquiti M2 Antenna Firmware 5.6.3 Description

Regulatory updates:

- New: Enable UNII2 band after Revised UNII Rules activation for certified models (United States/Puerto Rico)
- New: Revised UNII Rules activation for certified models: Rocket M5, NanoBridge M5, PowerBeamM5 300/400/620, NanoBeam M5 16/19
- Fix: Revised UK/DFS rules
- Fix: Disabled UNII2 frequencies for AP-Repeater after Revised UNII Rules gets activated (FCC regulatory restrictions)
- Fix: Limit channel width to 20MHz for Indonesia
- Fix: Reduce EIRP for Pakistan to 20dBm/100mW (5GHz)

Improvements:

- New: Linux kernel upgrade to 2.6.32.68 (possible fix for random AP reboots)
- New: DHCP server IP range is suggested according LAN IP address/netmask values
- New: Antenna model selection in Wireless page
- New: Allow to disable remote statistics reporting via Extra Reporting option in Advanced configuration page
- New: Default password change request before applying configuration changes

Fixes:

- airMAX: Security improvements
- Fix: Generate SSL certificate start date from firmware build timestamp
- Fix: Network settings are not fully loaded in case if bridge section is missing in configuration file
- Fix: AP crash prevention in power save mode
- Fix: Incorrect antenna selection for Rocket M900
- Fix: DFS AP doesn't change channel after NOL timeout
- Fix: Don't require to change default password if configuration backup was uploaded with updated credentials
- Fix: Egress traffic is limited on VLAN interfaces when rules are set on parent
- Fix: Simplified airView tool launch
- Fix: Enable airView for LiteBeam M5 23
- Fix: Optimise remote statistics collection to reduce infctld CPU usage
- Fix: Improve frequency scan for XW series radios
- Fix: PHP2 buffer overflow
- Fix: Station doesn't connect back to AP after it was kicked or AP was rebooted
- Fix: Reduce remote statistics bursts from AP and randomise transmit interval
- Fix: Remove Station only and airMAX only restriction for LiteBeam M5 23 product
- Fix: Improve AC2 agent response to server after device reboot
- Fix: Wrong frequency list after session timeout
- Fix: Respond on wireless interface for discovery requests when PPPoE client is configured
- Fix: Validate overlapping 30MHz width channels
- Fix: Enabling "Hide Indoor Channels" cause station to lockup
- Fix: wpa_supplicant no timestamp check
- WEB UI: Translations update
- WEB UI: Device Name displaying incorrectly when using symbol &
- WEB UI: Show possible LAN negotiation speed for gigabit capable devices
- WEB UI: TX Power reporting in MAIN page when set 0dBm
- WEB UI: Show antenna gain input field for devices which have single antenna option and no built-in antenna
- WEB UI: Show correct antenna in main tab if there are two antennas with same gain value
- WEB UI: Move Refresh button to top of the Stations list
- WEB UI: Hide TX signal in Station list if remote statistics are disabled
- WEB UI: TX power slide doesn't allow dragging

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Ubiquiti Drivers