Ubiquiti UAP-AC-IW-Pro Access Point Firmware 3.9.40.9098 Download

Posted at November 21, 2024 by PCI-DB Team

Ubiquiti UAP-AC-IW-Pro Access Point Firmware 3.9.40.9098 Description

Firmware changes since 3.9.27:

- [UAPG2/G3] Enable multi-hop wireless uplink on all (G2/G3) UAPs.
- [UAPG2/G3] Fix a couple issues with fast roaming when open SSIDs are also present.
- [UAPG2/G3] Fix guest portal support.
- [UAPG2/G3] Remove CCQ reporting from SNMP, as it is unsupported on these devices.
- [UAPG3] Add RADIUS authentication tracking.
- [UAPG3] Enable uplink priority support.
- [UAPG3] Fix L3 adoption issue.
- [UAPG2] Improve reliability under heavy load.
- [UAPG2] Fix 2.4GHz disconnect issue.
- [UAPG2] Fix priority uplink support.
- [UAPG2] Fix an issue with client reassociation for SSIDs with Fast Roaming enabled.
- [UAPG2] Fix a bug which may trigger a network loop when using wireless uplinks.
- [UAPG2] Fix broadcast leak when using DVLAN.
- [UAPG1] Fix SNMP support.
- [XG/BaseStationXG] Enable VHT160 support.
- [nanoHD] Add wireless uplink support.
- [nanoHD] Add support for priority uplink selection.
- [nanoHD] Add RF environment scanning.
- [nanoHD] Add RADIUS MAC Auth support.
- [nanoHD] Add UAPSD support for multi BSSIDs.
- [nanoHD] Add legacy device support.
- [nanoHD] Improve 5GHz rate control algorithm.
- [nanoHD] Improve auto channel selection.
- [nanoHD] Improve 2.4GHz auto channel selection.
- [nanoHD] Improve speed for non-guest VAPs, when guest VAPs are also present.
- [nanoHD] Bandsteering changes, bringing it inline with other UAPs (that support bandsteering).
- [nanoHD] Fix Ethernet status reporting.
- [nanoHD] Fix 802.11w support.
- [nanoHD] Fix broadcast filter.
- [nanoHD] Fix bandsteering disconnection issue.
- [nanoHD] Fix a potential RADIUS accounting bug.
- [nanoHD] Fix MAC ACL.
- [nanoHD] Fix a bug which caused the MAC address filter to not work in some cases.
- [nanoHD] Fix a bug with bandsteering so 2.4GHz only client STAs can connect (reported HERE).
- [nanoHD] Fix a bug that prevented client STAs from connecting to hidden 2.4GHz SSIDs.
- [nanoHD] Stability and performance improvements.
- [nanoHD] Remove old guest client STAs once disconnected from the network (reported HERE).
- [UAP] Add process restart and exit status events.
- [UAP] Add RTT latency tracking.
- [UAP] Add authentication tracking.
- [UAP] Improve client statistics reporting.
- [UAP] Fix a bug with MeshV3 wireless adoption.
- [UAP] Fix reported client STA signal.
- [UAP] Fix a print issue with stainfo, where RSSI bleeds into TX rate.
- [UAP] Fix TX retry accounting.
- [UAP] Fix uplink status reporting.
- [UAP] Fix rate limiting on non-guest SSIDs.
- [UAP] Fix the memory leak when using broadcast/multicast filter and RADIUS assigned VLANs.
- [UAP] Disable PMKSA caching by default.
- [USW] Add Port Security and MAC ACL support.
- [USW] Add 802.1X guest VLAN support.
- [USW] Restart DHCP client after a port is up.
- [USW] Fix LAN client stats when using LACP/LAG.
- [USW] Fix issue with default VLAN not working when using MAB.
- [USW] Fix ability to toggle flow control.
- [USW] Disable SNMP by default.
- [USW] Reduce max VLANs to 255 (default), which lowers memory use by ~10%.
- [HW] Add URL support for DHCP option 43.
- [HW] Several fast-apply provisioning improvements.
- [HW] Unify several modules across various UniFi platforms (UAP, USW and USG).
- [HW] Various bug fixes and improvements.
- [SEC] Security improvement.

About Access Point Firmware:

If you update the Access Point (AP) firmware, your device can benefit from changes that fix multiple issues encountered by wireless clients, correct different user interface problems, add various functionalities, and include support for newly developed protocols.

Before performing this task, we recommend that you read and understand all the installation steps, because there are many AP models and manufacturers available. Each producer strives to make the procedure as simple as possible, but there are cases when it's anything but that.

It is also advisable that you apply a new access point firmware in a steady power environment (UPS unit will satisfy this need), using an Ethernet cable rather than a wireless connection. The latter can be easily interrupted.

With this in mind, if you wish to apply this version, click the download button and install the package on your access point. Remember to check back with our website as often as possible so that you don't miss a single new release.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related Ubiquiti Drivers