Posted at December 22, 2024 by PCI-DB Team
Install Driver AutomaticallyDevice Name | Cisco RV130W Router Firmware 1.0.2.7 |
---|---|
Category | Router Switch Access Point |
Manufacturer | Cisco |
File Size | 18.4 MB |
Supported OS | OS Independent |
- GUI improvements.
- Support SNMP access from WAN side.
- Support certificates for IPSec VPN IKE authentication.
- Support DDNS update periodically.
- After rebooting or upgrading the device, schedule-based firewall access rules do not work. (CSCuo66872)
- If users enable QoS, configure the Ethernet upstream and downstream rate limit, and then create or delete a new VLAN, the downstream rate limit does not work. (CSCuo94504)
- Sometimes, after Ethernet WAN, or 3G interface failover, LAN hosts are unable to access the Internet. (CSCuo64951)
- Wireless clients may not be able to access the Internet when roaming between the device and another access point on the LAN side. (CSCum42666)
- OpenSSL upgrade. (CSCuo18651)
- Changing default LAN IP should be optional when VPN server is enabled. (CSCul19364)
- DNS proxy doesn’t always work. (CSCuo97062)
- DNS configuration was lost when configuring WAN in setup wizard. (CSCuo85131)
- Static DHP will only recognize ~44 entires. (CSCus89995)
- Changing default in LAN IP should be optional when VPN server is enabled. (CSCul19364)
- Save the downloadable package.
- Log into the router’s web user interface.
- Navigate to the firmware upgrade section of your wireless unit.
- Select the present firmware and configure your router to install this file.
- Wait as the device carries out this process.
- Reboot the unit if required.
Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.
Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.
In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.
If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.
If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.
If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device.
It is highly recommended to always use the most recent driver version available.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.
Device Type: Voip Voice Over Ip File Size: 15.7 MB OS Independent
Install DriverDevice Type: Router Switch Access Point File Size: 7.1 MB OS Independent
Install DriverDevice Type: Firmware File Size: 5.7 MB OS Independent
Install DriverDevice Type: Voip Voice Over Ip File Size: 13.7 MB OS Independent
Install DriverDevice Type: Voip Voice Over Ip File Size: 35.3 MB OS Independent
Install DriverDevice Type: Voip Voice Over Ip File Size: 13.7 MB OS Independent
Install DriverDevice Type: Voip Voice Over Ip File Size: 30 MB OS Independent
Install DriverDevice Type: Voip Voice Over Ip File Size: 30 MB OS Independent
Install DriverDevice Type: Router Switch Access Point File Size: 4.5 MB OS Independent
Install DriverDevice Type: Voip Voice Over Ip File Size: 7.9 MB OS Independent
Install DriverFind Missing Drivers
Recent Devices
Recent Drivers
© 2024 PCI-DB.com - PCI Database Replacement. All rights reserved.