Posted at November 21, 2024 by PCI-DB Team
Install Driver AutomaticallyDevice Name | NETGEAR WAC720 Access Point Firmware 3.1.4.0 |
---|---|
Category | Router Switch Access Point |
Manufacturer | NETGEAR |
File Size | 19.4 MB |
Supported OS | OS Independent |
- Added 2.4G 256QAM support in GUI.
- Fixed the issue where QoS policies as “traffic going to Source IP address as Voice traffic" is not working.
- Fixed the issue where the system time is not displayed properly when the AP is run over 7 days.
- Fixed the issue where the registration message keeps popping-up even AP is registered.
- Fixed the issue where the SNMP query for the data rates returns invalid values.
- Fixed the issue where the AP service discovery via mDNS (Bonjor) is not enabled with right platform names.
- Fixed the issue where the reset to factory default setting button does not reset DHCP/IP address to default.
- Clients fails to connect to the SSID when there is a high volume of multicast traffic is running in the network. Fix : enable multicast rate limiting.
- UCT is displayed instead of IST in current time under India time zone.
- In statistics Page, the Tx packets and bytes are inclusive of Multicast & Broadcast packets in Dashboard.
- AP shows only first 20 clients when it work in Ensemble mode and it expects admin to go to individual AP to see on rest of the clients.
- When administrator configures one of the APs in the Ensemble, then the AP will push the configuration to the rest of the Ensemble and assumes the control of the Ensemble.
- No way to select which channels to be used (or not to be used) for Auto Channel Allocation feature in Ensemble mode. Right now, we are forced to use all the channels.
- For 5Ghz Auto-channel logic will select from all non-DFS allowed channels for the current country code/revision list.
- For 2.4Ghz Auto-Channel logic will select 1, 6, 11 and it is hard coded.
- Weather channels 120,124,128 are not supported for EU countries.
- Download and extract the new firmware to a convenient place such as your desktop.
- Login to the AP web interface.
- Select Maintenance > Upgrade > Firmware Upgrade
- Click the Browse button and locate the image (.tar) upgrade file.
- Click the Apply button to initiate the upgrade process.
- During the upgrade process, the wireless access point automatically restarts. The upgrade process typically takes several minutes. When the Test LED turns off, wait a few more seconds before doing anything with the wireless access point.
If you update the Access Point (AP) firmware, your device can benefit from changes that fix multiple issues encountered by wireless clients, correct different user interface problems, add various functionalities, and include support for newly developed protocols.
Before performing this task, we recommend that you read and understand all the installation steps, because there are many AP models and manufacturers available. Each producer strives to make the procedure as simple as possible, but there are cases when it’s anything but that.
It is also advisable that you apply a new access point firmware in a steady power environment (UPS unit will satisfy this need), using an Ethernet cable rather than a wireless connection. The latter can be easily interrupted.
With this in mind, if you wish to apply this version, click the download button and install the package on your access point. Remember to check back with our website as often as possible so that you don’t miss a single new release.
It is highly recommended to always use the most recent driver version available.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.
Device Type: Router Switch Access Point File Size: 26.3 MB OS Independent
Install DriverDevice Type: Network Card File Size: 24.9 MB Windows XP ,Windows Vista ,Windows XP 64 bit ,Windows Vista 64 bit ,Windows 7 ,Windows 7 64 bit ,Windows 8 ,Windows 8 64 bit ,Windows 8.1 ,Windows 8.1
Install DriverDevice Type: Firmware File Size: 18.9 MB Windows 9X ,Windows ME ,Windows NT ,Windows 2K ,Windows XP ,Windows 2003 ,Windows Vista ,Windows XP 64 bit ,Windows 2008 ,Windows Vista 64 bit ,Window
Install DriverDevice Type: Router Switch Access Point File Size: 30.9 MB OS Independent
Install DriverDevice Type: Router Switch Access Point File Size: 14.7 MB OS Independent
Install DriverDevice Type: Network Card File Size: 20.2 MB Windows 9X ,Windows ME ,Windows NT ,Windows 2K ,Windows XP ,Windows 2003 ,Windows Vista ,Windows XP 64 bit ,Windows 2008 ,Windows Vista 64 bit ,Window
Install DriverDevice Type: Router Switch Access Point File Size: 14.7 MB OS Independent
Install DriverDevice Type: Router Switch Access Point File Size: 14.7 MB OS Independent
Install DriverDevice Type: Router Switch Access Point File Size: 30.9 MB OS Independent
Install DriverDevice Type: Firmware File Size: 7.4 MB Windows 9X ,Windows ME ,Windows NT ,Windows 2K ,Windows XP ,Windows 2003 ,Windows Vista ,Windows XP 64 bit ,Windows 2008 ,Windows Vista 64 bit ,Window
Install DriverFind Missing Drivers
Recent Devices
Recent Drivers
© 2024 PCI-DB.com - PCI Database Replacement. All rights reserved.