EnGenius EOC2611P Access Point Firmware 1.3.1 Download

Posted at April 27, 2024 by PCI-DB Team

EnGenius EOC2611P Access Point Firmware 1.3.1 Description

EOC2611P - 802.11g Outdoor High Power 600mW Bridge / Access Point with Dual Antenna Polarity & Dual Antennas

HARDWARE SPECIFICATIONS:
MCU/RF: Atheros AR2316
Memory: 32MB SDRAM
Flash: 8MB
Physical Interface
One 10/100 Fast Ethernet RJ-45
One Reset Button
One Antenna Switch
One RP-SMA Connector
LED Indicators:
1x Power (Status)
1x LAN (10/100Mbps)
1x WLAN (Wireless Activity)
3x Link Quality (Client Bridge mode)
Green: Excellent Quality / Yellow: Good Quality / Red: Poor Quality
Power Requirements:
Active Ethernet: (Power-over-Ethernet) Proprietary PoE Design
Power Adapter: 24V/0.6A DC
Regulation Certifications: FCC Part 15C/15B, EN 300 328/EN 301 489-1/-17, EN60950

RF SPECIFICATIONS:
Frequency Band: 2.412~2.472GHz
Modulation Technology: OFDM: BPSK, QPSK, 16-QAM, 64-QAM, DSSS: DBPSK, DQPSK, CCK
Operating Channels: 11 for North America / 14 for Japan / 13 for Europe
Receive Sensitivity (Typical):
IEEE 802.11g
-92dBm @ 6Mbps
-74dBm @ 54Mbps
IEEE 802.11b
-97dBm @ 1Mbps
-89dBm @ 11Mbps
Available Transmit Power (Average):
IEEE 802.11g
28dBm @ 6~24Mbps
26dBm @ 36Mbps
24dBm @ 48Mbps
23dBm @ 54Mbps
IEEE 802.11b
28dBm @ 1~11Mbps
Antenna:
Internal: Directional Panel Antenna; Peak Gain 10dBi
Horizontal -3dB Bandwidth: 70°
Vertical -3dB Bandwidth: 35°
Antenna Polarity: Dual-Polarized; Vertical/Horizontal
Polarity Selection: Software Controlled
External: RP-SMA Female Type

SOFTWARE FEATURES:
Topology: Infrastructure
Protocol / Standard: 802.3 (Ethernet) / 802.3u (Fast Ethernet) / 802.11b/g (2.4GHz WLAN)
Operation Mode: Access Point / Client Bridge / Client Router / WDS
LAN: DHCP Server / DHCP Client
VPN: VPN - pass through
Wireless:
Channel Selection (Setting varies by countries)
Transmission Rate 802.11b/g: 108(SuperG), 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1 in Mbps
Long Distance Transmission: 1km to 30km
Transmit Power Table
Signal Strength LED Indicators (3 colors)
Narrow Bandwidth Support 5/10/20MHz
PING Function and Trace Route Function
PPPoE (Client Router mode)
Multiple SSID Support (up to 4)(Access Point mode)
802.1q VLAN Tagging Support
Security:
WEP Encryption 64/128/152bits
WPA/WPA2 Personal (WPA-PSK using TKIP or AES)
WPA/WPA2 Enterprise (WPA-EAP using TKIP)
802.1x Authenticator
Hide SSID in Beacons
MAC Address Filtering (up to 50)
Wireless STA (Client) Connected List
QoS: WMM

MANAGAMENT:
Configuration: Web-Based Configuration (HTTP)
Firmware Upgrade: Upgrade Firmware via Web Browser / Keep Latest Setting When Firmware Update
Administrator Setting: Administrator Password Change
Reset Setting: Reboot (Press 1 second) / Reset to Factory Default (Press 5 seconds)
System Monitoring: Status, Event Log
SNMP: V1, V2c
MIB: MIB I, MIB II (RFC1213) and Private MIB
Backup & Restore: Settings Through Web
Time Setting: NTP (Auto Setting) / Manual Change

ENVIRONMENT & PHYSICAL:
Temperature Range: Operation -20°C to 70°C (-4°F to 158°F) / Storage -30°C to 80°C (-22°F to 176°F)
Humidity (Non-condensing): 0%~90% Typical
Dimensions: Length: 10.24” (260mm) x Width: 3.31” (84mm) x Height: 2.17” (55mm)
Weight: 0.84lb. (380g)

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related EnGenius Drivers