EnGenius ECB9500 Access Point Firmware 2.2.9 Download

Posted at December 3, 2024 by PCI-DB Team

EnGenius ECB9500 Access Point Firmware 2.2.9 Description

Wireless N 300Mbps Access Point / Bridge / Repeater / Router with Gigabit & 802.3af PoE

HARDWARE SPECIFICATIONS:
MCU: RT2880, 266MHz
Memory: 32MB SDRAM
Flash: 8MB
Physical Interface:
LAN One 10/100/1000 Gigabit Ethernet
Reset Button
Power Jack
WPS Push Button (Wi-Fi Protected Setup)
LED’s Status:
Power (Status)
LAN (10/100/1000Mbps)
WLAN (Wireless Connection)
Power Requirements:
Power Supply: 90 to 240VDC ± 10% 50/60Hz (Depends on different countries)
Active Ethernet: (Power-over-Ethernet, IEEE 802.3af) 48VDC/0.375A
Device: 12V/1A
Regulation Certifications: FCC Part 15/UL, CE

RF SPECIFICATIONS:
Frequency Band: 2.400–2.484GHz
Media Access Protocol: Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA)
Modulation Technology: OFDM: BPSK, QPSK, 16-QAM, 64-QAM, DBPSK, DQPSK, CCK
Operation Channels: 11 for North America
Receive Sensitivity (Typical):
IEEE 802.11n
MCS8 @ -91dBm
MCS15 @ -74dBm
IEEE 802.11g
6Mbps @ -92dBm
54Mbps @ -75dBm
IEEE 802.11b
1Mbps @ -93dBm
11Mbps @ -91dBm
Available Transmit Power:
IEEE 802.11n/g
19dBm @ 6~9Mbps / MCS9
18dBm @ 12~18Mbps / MCS11
17dBm @ 24~36Mbps / MCS13
16dBm @ 48~54Mbps / MCS15
IEEE 802.11b
18dBm @ 1~11Mbps
Antenna: Detachable Omni Antenna x3; RP-TNC Type; Peak Gain 5dBi
Impedance: 50ohm
Frequency Range: 0~6GHz
V.S.W.R.: 1.5 (Max)
Working Voltage: <=500Vrms
Dielectric Withstanding Voltage: <=1500Vrms
Insulation Resistance: >=5000Megohms
Contact Resistance: Center contact 1.5Milliohms (Max) / Outer contact 0.2Milliohms (Max)

SOFTWARE FEATURES:
Topology: Infrastructure
Operation Mode: Client Bridge / Access Point / WDS AP / WDS Bridge / Client Router / Router / Universal Repeater
LAN: DHCP Server / DHCP Client
Wireless:
Wireless Mode 802.11b / 802.11g / 802.11n
Channel Selection (Setting varies by Country)
Signal Strength
Bandwidth Selection 40/20MHz
Transmission Rate
802.11b/g: 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1 in Mbps
802.11n

Security:
WEP Encryption 64/128bits
WPA Personal (WPA-PSK using TKIP or AES)
WPA Enterprise (WPA-EAP using TKIP)
802.1x Authenticator
802.1x Supplicant MD5/TTLS (Client Bridge & Client Router mode)
Hide SSID in Beacons
Multiple SSID with 802.1q VLAN Tagging (up to 4 SSID)(Access Point mode)
MAC Filter (Access Point mode)
WLAN L2 Isolation (Access Point mode)
Wireless STA (Client) Connected List
QoS: WMM

MANAGEMENT:
Configuration: Web-Based Configuration (HTTP) / Telnet
Firmware Upgrade: Upgrade Firmware via Web Browser; Keep Latest Setting When Firmware Update
Administrator Setting: Administrator Password Change
Reset Setting: Reboot / Reset to Factory Default
System Monitoring: Status, Statistics and Event Log
SNMP: v1, v2c
MIB: MIB I, MIB II (RFC1213), and Private MIB
Traffic Measurement: Per Interface
Bandwidth Measurement: IP Range & Bandwidth Management
Backup & Restore: Settings Through Web

ENVIRONMENT & PHYSICAL:
Temperature Range: Operation 0°C to 45°C (32°F to 113°F) / Storage -20°C to 70°C (-4°F to 158°F)
Humidity (Non-condensing): 5% ~ 95% Typical
Dimensions: L: 4.92” (125mm) x W: 4.25” (108mm) x H: 1.22” (31mm)
Weight: 0.77lb. (350g)

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related EnGenius Drivers