EnGenius ECB3500 Access Point Firmware 1.3.4 Download

Posted at December 22, 2024 by PCI-DB Team

EnGenius ECB3500 Access Point Firmware 1.3.4 Description

802.11g High Power 600mW Wireless Access Point / Bridge / Repeater / Router with Antenna Diversity & 802.3af PoE

HARDWARE SPECIFICATIONS:
MCU: Atheros AR2316, 180MHz
Memory: 32MB SDRAM
Flash: 8MB
Physical Interface:
LAN One 10/100 Fast Ethernet RJ-45
Reset Button
Power Jack
LED’s Status:
Power (Status)
LAN (10/100Mbps)
WLAN (Wireless Connection)
Power Requirements:
Power Supply: 90 to 240VDC ± 10%, 50/60Hz (Depends on different countries)
Active Ethernet: (Power-over-Ethernet, IEEE 802.3af) 48VDC/0.375A
Device: 12V/1A
Regulation Certifications: FCC Part 15, CE

RF SPECIFICATIONS:
Frequency Band: 2.400–2.484GHz
Media Access Protocol: Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA)
Modulation Technology: OFDM: BPSK, QPSK, 16-QAM, 64-QAM, DBPSK, DQPSK, CCK
Operation Channels: 11 for North America
Receive Sensitivity (Typical):
IEEE 802.11g
6Mbps @ -92dBm
54Mbps @ -74dBm
IEEE 802.11b
1Mbps @ -97dBm
11Mbps @ -89dBm
Available Transmit Power:
IEEE 802.11g
26dBm @ 6~24Mbps
25dBm @ 36Mbps
23dBm @ 48Mbps
22dBm @ 54Mbps
IEEE 802.11b
27dBm @ 1~11Mbps
Antenna: Detachable Omni Antenna x2; RP-TNC Type; Peak Gain 5dBi

SOFTWARE FEATURES:
Topology: Infrastructure
Operation Mode: Client Bridge / Access Point / WDS AP / WDS Bridge / Client Router / AP Router / Universal Repeater
LAN: DHCP Server / DHCP Client
WAN (Client Router / AP Router mode): PPPoE
Router: NAT / NAPT
VPN: VPN pass-through (PPTP, L2TP, IPSEC)
Wireless:
Wireless Mode 802.11b / 802.11g / SuperG
Channel Selection (Setting varies by Country)
Transmission Rate 802.11b/g: 108, 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1 in Mbps
Transmit Output Power Control
Signal Strength
Security:
WEP Encryption 64/128/152bits
WPA Personal (WPA-PSK using TKIP or AES)
WPA Enterprise (WPA-EAP using TKIP)
802.1x Authenticator (Access Point mode)
802.1x Supplicant-TTLS (Client Bridge mode)
Hide SSID in Beacons
Multiple SSID with 802.1q VLAN Tagging (up to 4 SSID)(Access Point mode)
MAC Filter (Access Point mode)
L2 Isolation (Access Point mode)
Wireless STA (Client) Connected List
Lock to AP MAC (Client Bridge mode)
QoS: WMM

MANAGEMENT:
Configuration: Web-Based Configuration (HTTP) / Telnet
Firmware Upgrade: Upgrade Firmware via Web Browser; Keep Latest Setting When Firmware Update
Administrator Setting: Administrator Password Change
Reset Setting: Reboot (Press 1 second) / Reset to Factory Default (Press 5 seconds)
System Monitoring: Status, Statistics and Event Log
SNMP: v1, v2c
MIB: MIB I, MIB II
Backup & Restore: Settings Through Web

ENVIRONMENT & PHYSICAL:
Temperature Range: Operation 0°C to 45°C (32°F to 113°F) / Storage -20°C to 70°C (-4°F to 158°F)
Humidity (Non-condensing): 5% ~ 95% Typical
Dimensions: L: 4.92” (125mm) x W: 4.25” (108mm) x H: 1.22” (31mm)
Weight: 0.77lb. (350g)

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.

Related EnGenius Drivers